M37542F8FP Renesas Electronics America, M37542F8FP Datasheet - Page 45

• Manufacturer Part Number: M37542F8FP
• Description: IC 740 MCU FLASH 32K 36SSOP
• Manufacturer: Renesas Electronics America
• Series: 740/38000r

Specifications of M37542F8FP

• Core Processor: 740
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SIO, UART/USART
• Peripherals: POR, WDT
• Number Of I /o: 29
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 36-SSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Input capture
7542 group has 2-input capture channels. Each channel (0 and 1)
has the same function and can be used to capture count value of
either Timer A or Timer B.
The source timer for each channel is selected by setting value of
the capture x (x = 0, 1) timer source bit. Timer A and Timer B can
be selected for the source timer to each channel, respectively.
To use each capture channel, set the capture x input port bits and
set the port direction register corresponding to capture channel to
input mode.
The input capture circuit retains the count value of selected timer
when external trigger is input. The timer count value is retained to
the capture latch x0 when rising edge is input and is retained to
the capture latch x1 when falling edge is input.
The count value of timer can be retained by software by capture y
(y = 00, 01, 10, 11) software trigger bit too. When “1” is set to this
bit, count value of timer is retained to the corresponded capture
latch.
When reading from the capture y software trigger bit is executed,
“0” is read out.
The latest status of capture latch can be confirmed by reading of
the capture x status bit. This bit indicates the capture latch which
latest data is in.
The valid trigger edge for capture interrupt is set by the capture x
interrupt edge selection bits. (Regardless of the setting value of
capture x interrupt edge selection bits, timer count values for both
edges are retained to the capture latch.)
Each capture input has the noise filter circuit that judges continu-
ous 4-time same level with sampling clock to be valid. The
sampling clock of noise filter is set by the capture x noise filter
clock selection bits.
Reading from the register for each channel is controlled by setting
value of the capture register read pointer. Reading from each reg-
ister is in the following order;
1.Set the value of the corresponded input capture channel to the
2.Read from the capture register (low-order) and capture register
7542 Group
Rev.3.03
REJ03B0006-0303
capture register read pointer.
(high-order).
Jul 11, 2008
Page 43 of 117
• If the capture trigger is input while the capture register (low-order
• When the on-chip-oscillator is selected for Timer A count source,
• When writing “1” to capture latch x0 (x1) software trigger bit of
• When setting the interrupt active edge selection bit and noise fil-
• When the capture interrupt is used as the interrupt for return
Set the interrupt edge selection bit or noise filter clock selection bit.
and high-order) is in read, captured value is changed between
high-order reading and low-order reading. Accordingly, some
countermeasure by software is recommended, for example
comparing the values that twice of read.
Timer A cannot be used for the capture source timer.
Timer B cannot be used for the capture source timer when the
system is in the following state;
• CPU operation clock source: X
• Timer B count source: Timer A underflow
• Timer A count source: On-chip oscillator output
capture latch x0 and x1 at the same time, or external trigger and
software trigger occur simultaneously, the set value of capture x
status bit is undefined.
ter clock selection bit of external interrupt CAP
interrupt request bit may be set to “1”.
When not requiring the interrupt occurrence synchronized with
these setting, take the following sequence.
Set the corresponding interrupt enable bit to “0” (disabled).
Set the corresponding interrupt request bit to “0” after 1 or more
instructions have been executed.
Set the corresponding interrupt enable bit to “1” (enabled).
from stop mode, set the capture x noise filter clock selection bits
to “00 (Filter stop)”.
Notes on Input Capture
IN
oscillation
0
, CAP
1
, the