C8051F537-IM Silicon Laboratories Inc, C8051F537-IM Datasheet - Page 77

• Manufacturer Part Number: C8051F537-IM
• Description: IC 8051 MCU 2K FLASH 20QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F53xr

Specifications of C8051F537-IM

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.25 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 20-QFN
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.25 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 336-1400

less than 100 nA. See Section “13.1. Priority Crossbar Decoder” on page 121 for details on configuring
Comparator outputs via the digital Crossbar. Comparator inputs can be externally driven from –0.25 V to
(V
in Table 2.6 on page 31.
The Comparator response time may be configured in software via the CPTnMD register (see SFR Defini-
tion 7.3). Selecting a longer response time reduces the Comparator supply current. See Table 2.6 on
page 31 for complete timing and current consumption specifications.
The Comparator hysteresis is software-programmable via its Comparator Control register CPT0CN. The
user can program both the amount of hysteresis voltage (referred to the input voltage) and the positive and
negative-going symmetry of this hysteresis around the threshold voltage.
The Comparator hysteresis is programmed using Bits3–0 in the Comparator Control Register CPT0CN
(shown in SFR Definition 7.1). The amount of negative hysteresis voltage is determined by the settings of
the CP0HYN bits. As shown in Table 2.6 on page 31, settings of 20, 10 or 5 mV of negative hysteresis can
be programmed, or negative hysteresis can be disabled. In a similar way, the amount of positive hysteresis
is determined by the setting the CP0HYP bits.
Comparator interrupts can be generated on both rising-edge and falling-edge output transitions. (For Inter-
rupt enable and priority control, see Section “10. Interrupt Handler” on page 98). The CP0FIF flag is set to
logic 1 upon a Comparator falling-edge detect, and the CP0RIF flag is set to logic 1 upon the Comparator
rising-edge detect. Once set, these bits remain set until cleared by software. The output state of the Com-
parator can be obtained at any time by reading the CP0OUT bit. The Comparator is enabled by setting the
CP0EN bit to logic 1 and is disabled by clearing this bit to logic 0. When the Comparator is enabled, the
internal oscillator is awakened from SUSPEND mode if the Comparator output is logic 0.
REGIN
) + 0.25 V without damage or upset. The complete Comparator electrical specifications are given
(Programmed with CP0HYP Bits)
Positive Hysteresis Voltage
INPUTS
OUTPUT
VIN+
VIN-
CIRCUIT CONFIGURATION
Positive Hysteresis
CP0-
VIN+
CP0+
VIN-
V
Disabled
OL
Figure 7.2. Comparator Hysteresis Plot
V
OH
+
_
CP0
C8051F52x/F52xA/F53x/F53xA
Positive Hysteresis
Maximum
OUT
Rev. 1.3
Negative Hysteresis
Disabled
Negative Hysteresis
(Programmed by CP0HYN Bits)
Maximum
Negative Hysteresis Voltage
77