PIC24FJ64GA306-I/MR Microchip Technology, PIC24FJ64GA306-I/MR Datasheet - Page 351

• Manufacturer Part Number: PIC24FJ64GA306-I/MR
• Description: 16-bit, 16 MIPS, 64 KB Flash, 8 KB RAM, 53 I/O, LCD, XLP W/Vbat 64 QFN 9x9x0.9mm
• Manufacturer: Microchip Technology

31.0
The PIC24F instruction set adds many enhancements
to the previous PIC
taining an easy migration from previous PIC MCU
instruction sets. Most instructions are a single program
memory word. Only three instructions require two
program memory locations.
Each single-word instruction is a 24-bit word divided
into an 8-bit opcode, which specifies the instruction
type and one or more operands, which further specify
the operation of the instruction. The instruction set is
highly orthogonal and is grouped into four basic
categories:
• Word or byte-oriented operations
• Bit-oriented operations
• Literal operations
• Control operations
Table 31-1
describing the instructions. The PIC24F instruction set
summary in
with the status flags affected by each instruction.
Most word or byte-oriented W register instructions
(including
operands:
• The first source operand, which is typically a
• The second source operand, which is typically a
• The destination of the result, which is typically a
However, word or byte-oriented file register instructions
have two operands:
• The file register specified by the value, ‘f’
• The destination, which could either be the file
Most
rotate/shift instructions) have two operands:
• The W register (with or without an address
• The bit in the W register or file register
 2010-2011 Microchip Technology Inc.
Note:
register, ‘Wb’, without any address modifier
register, ‘Ws’, with or without an address modifier
register, ‘Wd’, with or without an address modifier
register, ‘f’, or the W0 register, which is denoted
as ‘WREG’
modifier) or file register (specified by the value of
‘Ws’ or ‘f’)
(specified by a literal value or indirectly by the
contents of register, ‘Wb’)
bit-oriented
INSTRUCTION SET SUMMARY
This chapter is a brief summary of the
PIC24F instruction set architecture and is
not intended to be a comprehensive
reference source.
barrel
shows the general symbols used in
Table 31-2
®
shift
MCU instruction sets, while main-
instructions
lists all the instructions, along
instructions)
(including
have
PIC24FJ128GA310 FAMILY
simple
three
The literal instructions that involve data movement may
use some of the following operands:
• A literal value to be loaded into a W register or file
• The W register or file register where the literal
However, literal instructions that involve arithmetic or
logical operations use some of the following operands:
• The first source operand, which is a register, ‘Wb’,
• The second source operand, which is a literal
• The destination of the result (only if not the same
The control instructions may use some of the following
operands:
• A program memory address
• The mode of the table read and table write
All instructions are a single word, except for certain
double-word
double-word instructions so that all the required infor-
mation is available in these 48 bits. In the second word,
the 8 MSbs are ‘0’s. If this second word is executed as
an instruction (by itself), it will execute as a NOP.
Most single-word instructions are executed in a single
instruction cycle, unless a conditional test is true or the
program counter is changed as a result of the instruc-
tion. In these cases, the execution takes two instruction
cycles, with the additional instruction cycle(s) executed
as a NOP. Notable exceptions are the BRA (uncondi-
tional/computed branch), indirect CALL/GOTO, all table
reads and writes, and RETURN/RETFIE instructions,
which are single-word instructions but take two or three
cycles.
Certain instructions that involve skipping over the sub-
sequent instruction require either two or three cycles if
the skip is performed, depending on whether the
instruction being skipped is a single-word or two-word
instruction. Moreover, double-word moves require two
cycles. The double-word instructions execute in two
instruction cycles.
register (specified by the value of ‘k’)
value is to be loaded (specified by ‘Wb’ or ‘f’)
without any address modifier
value
as the first source operand), which is typically a
register, ‘Wd’, with or without an address modifier
instructions
instructions,
which
DS39996F-page 351
were
made