DS26518GN+ Maxim Integrated Products, DS26518GN+ Datasheet - Page 24

• Manufacturer Part Number: DS26518GN+
• Description: IC TXRX T1/E1/J1 8PORT 256-CSBGA
• Manufacturer: Maxim Integrated Products
• Type: Transceiverr

Specifications of DS26518GN+

• Number Of Drivers/receivers: 8/8
• Protocol: T1/E1/J1
• Voltage - Supply: 3.135 V ~ 3.465 V
• Mounting Type: Surface Mount
• Package / Case: 256-CSBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

RMSYNC1/
RMSYNC2/
RMSYNC3/
RMSYNC4/
RMSYNC5/
RMSYNC6/
RMSYNC7/
RMSYNC8/
RCHBLK1/
RCHBLK2/
RCHBLK3/
RCHBLK4/
RCHBLK5/
RCHBLK6/
RCHBLK7/
RCHBLK8/
RFSYNC1
RFSYNC2
RFSYNC3
RFSYNC4
RFSYNC5
RFSYNC6
RFSYNC7
RFSYNC8
RCHCLK1
RCHCLK2
RCHCLK3
RCHCLK4
RCHCLK5
RCHCLK6
RCHCLK7
RCHCLK8
RLF/LTC1
BPCLK1
RSIG1
RSIG2
RSIG3
RSIG4
RSIG5
RSIG6
RSIG7
RSIG8
CLKO/
NAME
N12
D11
R11
R13
C12
G13
P10
E12
A12
F12
T11
T13
PIN
M5
C4
C6
P4
P6
D4
E6
R5
E4
B5
E8
D3
L6
T5
Output
Output
Output
Output
Output
TYPE
Receive Multiframe/Frame Synchronization 1 to 8. A dual function pin to
indicate frame or multiframe synchronization. RFSYNCn is an extracted 8kHz
pulse, one RCLKn wide that identifies frame boundaries. RMSYNCn is an
extracted pulse, one RCLKn wide (elastic store disabled) or one RSYSCLKn wide
(elastic store enabled), that identifies multiframe boundaries. When the receive
elastic store is enabled, the RMSYNCn signal indicates the multiframe sync on
the system (backplane) side of the elastic store. In E1 mode, this pin can indicate
either the CRC-4 or CAS multiframe as determined by the RSMS2 control bit in
the Receive I/O Configuration register (RIOCR.1).
Receive Signaling 1 to 8. Outputs signaling bits in a PCM format. Updated on
rising edges of RCLKn when the receive-side elastic store is disabled. Updated
on the rising edges of RSYSCLKn when the receive-side elastic store is enabled.
See
Receive Channel Block/Receive Channel Block Clock. This pin can be
configured to output either RCHBLK or RCHCLK.
RCHBLK[1:8]. RCHBLKn is a user-programmable output that can be forced high
or low during any of the 24 T1 or 32 E1 channels. It is synchronous with RCLKn
when the receive-side elastic store is disabled. It is synchronous with RSYSCLKn
when the receive-side elastic store is enabled. This pin is useful for blocking
clocks to a serial UART or LAPD controller in applications where not all channels
are used such as fractional service, 384kbps service, 768kbps, or ISDN-PRI. Also
useful for locating individual channels in drop-and-insert applications, for external
per-channel loopback, and for per-channel conditioning.
RCHCLK[1:8]. RCHCLKn is a 192kHz (T1) or 256kHz (E1) clock that pulses high
during the LSB of each channel. It is synchronous with RCLKn when the receive-
side elastic store is disabled. It is synchronous with RSYSCLKn when the
receive-side elastic store is enabled. It is useful for parallel-to-serial conversion of
channel data.
Backplane Clock 1. Programmable clock output that can be set to 2.048MHz,
4.096MHz, 8.192MHz, or 16.384MHz. The reference for this clock can be
RCLK[8:1], a 1.544MHz or 2.048MHz clock frequency derived from MCLK, or an
external reference clock (REFCLKIO). This allows system clocks to be referenced
from external sources, the T1J1E1 recovered clocks, or the MCLK oscillator.
Clock Out. Clock output pin that can be programmed to output numerous
frequencies referenced to MCLK. Frequencies available: 1.544MHz, 2.048MHz,
4.096MHz, 8.192MHz, 12.288MHz, 16.384MHz, 256kHz, and 64kHz.
GTCCR3.CLKOSEL[2:0] selects the frequency.
Receive Loss of Frame/Loss of Transmit Clock. This pin can also be
programmed to either toggle high when the synchronizer is searching for the
frame and multiframe, or to toggle high if the TCLKn pin has not been toggled for
approximately three clock periods.
RLF/LTC1 is available on the DS26518 when GTCR1.528MD = 1.
Table
24 of 312
9-7.
FUNCTION