PIC16F913-I/SP Microchip Technology Inc., PIC16F913-I/SP Datasheet - Page 130

• Manufacturer Part Number: PIC16F913-I/SP
• Description: 28 PIN, 7 KB FLASH, 352 RAM, 25 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F913-I/SP

• A/d Inputs: 5-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 5 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 25
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin SPDIP
• Programmable Memory: 7K Bytes
• Ram Size: 256 Bytes
• Speed: 20 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC16F917/916/914/913
REGISTER 11-2:
DS41250E-page 128
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
RCSTA – RECEIVE STATUS AND CONTROL REGISTER (ADDRESS 18h)
bit 7
SPEN
1 = Serial port enabled (configures RC7/RX/DT/SDI/SDA/SEG8 and
0 = Serial port disabled
RX9: 9-bit Receive Enable bit
1 = Selects 9-bit reception
0 = Selects 8-bit reception
SREN: Single Receive Enable bit
Asynchronous mode:
Don’t care
Synchronous mode – Master:
1 = Enables single receive
0 = Disables single receive
This bit is cleared after reception is complete
Synchronous mode – Slave:
Don’t care.
CREN: Continuous Receive Enable bit
Asynchronous mode:
1 = Enables continuous receive
0 = Disables continuous receive
Synchronous mode:
1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN)
0 = Disables continuous receive
ADDEN: Address Detect Enable bit
Asynchronous mode 9-bit (RX9 = 1):
1 = Enables address detection, enables interrupt and load of the receive buffer when RSR<8>
0 = Disables address detection, all bytes are received and ninth bit can be used as parity bit
FERR: Framing Error bit
1 = Framing error (can be updated by reading RCREG register and receive next valid byte)
0 = No framing error
1 = Overrun error (can be cleared by clearing bit CREN)
0 = No overrun error
Legend:
R = Readable bit
- n = Value at POR
OERR: Overrun Error bit
RX9D: 9th bit of Received Data (can be parity bit but must be calculated by user firmware)
R/W-0
SPEN
Note 1: CCP2CON used for PIC16F914/917 only.
RC6/TX/CK/SCK/SCL/SEG9 pins as serial port pins)
is set
(1)
: Serial Port Enable bit
R/W-0
RX9
R/W-0
SREN
Preliminary
W = Writable bit
‘1’ = Bit is set
R/W-0
CREN
ADDEN
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
FERR
R-0
© 2005 Microchip Technology Inc.
x = Bit is unknown
OERR
R-0
RX9D
R-x
bit 0