DP83865-EB National Semiconductor, DP83865-EB Datasheet - Page 73
DP83865-EB
Manufacturer Part Number
DP83865-EB
Description
BOARD EVALUATION DP83865
Manufacturer
National Semiconductor
Datasheet
1.DP83865BVH.pdf
(86 pages)
Specifications of DP83865-EB
Main Purpose
Interface, Ethernet
Utilized Ic / Part
DP83865
Lead Free Status / RoHS Status
Not applicable / Not applicable
- Current page: 73 of 86
- Download datasheet (592Kb)
6.0 Electrical Specifications
6.2 Reset Timing
V
T1
T2
T3
T4
T5
Note 1: Guaranteed by design. Not tested.
Note 2: It is recommended to use external pull-up and/or pull-down resistors for each of the hardware configuration pins that provide fast RC time con-
stants in order to latch-in the proper value prior to the pin transitioning to an output driver. Unless otherwise noted in the Pin Description section all
external pull-up or pull-down resistors are recommended to be 2k
Parameter
DD
3.3V (I/O if applicable)
Latch-In of Hardware
1.8V (core, analog),
2.5V (I/O, analog),
Configuration Pins
CLK_TO_MAC
Reference clock settle time The reference clock must be stable af-
Hardware RESET Pulse
Width
Post RESET Stabilization
time prior to MDC preamble
for register accesses
External pull configuration
latch-in time from the deas-
sertion of RESET
CLK_TO_MAC Output Sta-
bilization Time
CLK_IN
RESET
MDC
Description
(Continued)
ter the last power supply voltage has
settled and before RESET is deas-
serted. (Note 1)
Pins VDD_SEL and CLK_MAC_EN
are latched in during this time.
Power supply voltages and the refer-
ence clock (CLK_IN) have to be sta-
ble.
MDIO is pulled high for 32-bit serial
management initialization.
Hardware Configuration Pins are de-
scribed in the Pin Description section.
Reset includes external hardware and
internal software through registers.
(Note 2)
If enabled, the CLK_TO_MAC output,
being independent of RESET, power-
down mode and isolation mode, is
available after power-up.
CLK_TO_MAC is a buffered output
CLK_IN. (Note 1)
T1
73
T5
Notes
T2
T3
T4
0 + T1
Min
150
20
20
0
32 clocks
Typ
Max
www.national.com
Units
ms
ms
s
s
s
Related parts for DP83865-EB
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
National Semiconductor [8-Bit D/A Converter]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [Media Coprocessor]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
AC97 Rev 2 Codec with Sample Rate Conversion and National 3D Sound
Manufacturer:
National Semiconductor
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
8-bit 20 MSPS flash A/D converter.
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Low Noise Quad Operational Amplifier
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad Differential Line Receivers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad High Speed Trapezoidal? Bus Transceiver
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Dual Line Receiver
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
TTL to 10k ECL Level Translator with Latch
Manufacturer:
National Semiconductor
Datasheet: