PIC16F1824-I/P Microchip Technology, PIC16F1824-I/P Datasheet - Page 277

• Manufacturer Part Number: PIC16F1824-I/P
• Description: IC PIC MCU 8BIT 14KB FLSH 14PDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1824-I/P

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 11
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 14-DIP (0.300", 7.62mm)
• Processor Series: PIC16F
• Core: PIC
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

25.6.4 I
To initiate a Start condition, the user sets the Start
Enable bit, SEN bit of the SSP1CON2 register. If the
SDA and SCL pins are sampled high, the Baud Rate
Generator
SSP1ADD<7:0> and starts its count. If SCL and SDA
are both sampled high when the Baud Rate Generator
times out (T
of the SDA being driven low while SCL is high is the
Start condition and causes the S bit of the SSP1STAT1
register to be set. Following this, the Baud Rate Gen-
erator is reloaded with the contents of SSP1ADD<7:0>
and resumes its count. When the Baud Rate Genera-
tor times out (T
FIGURE 25-26:
 2010 Microchip Technology Inc.
CONDITION TIMING
2
C MASTER MODE START
BRG
is
), the SDA pin is driven low. The action
BRG
reloaded
), the SEN bit of the SSP1CON2
FIRST START BIT TIMING
Write to SEN bit occurs here
with
SDA
SCL
the
contents
SDA = 1,
SCL = 1
T
BRG
Preliminary
of
S
Set S bit (SSP1STAT<3>)
T
BRG
At completion of Start bit,
hardware clears SEN bit
register will be automatically cleared by hardware; the
Baud Rate Generator is suspended, leaving the SDA
line held low and the Start condition is complete.
and sets SSP1IF bit
PIC16(L)F1824/1828
Note 1: If at the beginning of the Start condition,
Write to SSP1BUF occurs here
T
BRG
2: The Philips I
1st bit
the SDA and SCL pins are already sam-
pled low, or if during the Start condition,
the SCL line is sampled low before the
SDA line is driven low, a bus collision
occurs, the Bus Collision Interrupt Flag,
BCL1IF, is set, the Start condition is
aborted and the I
its Idle state.
bus collision cannot occur on a Start.
T
BRG
2
C Specification states that a
2nd bit
2
C module is reset into
DS41419B-page 277