tmp88cs34ng TOSHIBA Semiconductor CORPORATION, tmp88cs34ng Datasheet - Page 4

• Manufacturer Part Number: tmp88cs34ng
• Description: Cmos 8-bit Microcontroller
• Manufacturer: TOSHIBA Semiconductor CORPORATION

Pin Functions (1/2)
P20 (
P35 (SDA0)
P34 (SCL0)
P33 (TC4)
P32
P31 (INT4/TC3)
P30 (INT3/RXIN)
P47
P46
P45
P44
P43 (
P42 (
P41 (
P40 (
P57 (I)
P56 (
P55 (
P54 (
P53
(
/INT2/
P52 (SDA1/SO1)
P51 (SCL1/SI1)
P50 (TC2/
P67 (Y/BL)
P66 (B)
P65 (G)
P64 (R)
P63 (RIN)
P62 (GIN)
P61
(
P60
(
KWU0
KWU5
KWU4
Pin Name
INT5
PWM3
PWM2
PWM1
PWM0
KWU3
KWU2
KWU1
SCK1
/AIN0/TC1
/BIN/AIN5)
/YBLIN/AIN4)
/
INT0
STOP
/AIN1)
)
)
/AIN3)
/AIN2)
)
)
)
)
)
(Input/Output/Output)
(Input/Output/Input)
I/O (Input/Output)
I/O (Input/Output)
(Input/Input/Input
/Input/Output)
(Input/Input)
I/O (Output)
I/O (Output)
I/O (Output)
I/O (Output)
I/O (Output)
I/O (Output)
I/O (Output)
I/O (Output)
I/O (Output)
I/O (Input)
I/O (Input)
I/O (Input)
I/O (Input)
I/O (Input)
I/O (Input)
I/O (Input)
I/O (Input)
I/O (Input)
I/O (Input)
I/O (Input)
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
1-bit input/output port with latch.
When used as an input port, the
latch must be set to “1”.
6-bit programmable input/output
port. Each bit of these ports can be
individually configured as an input or
an output under software control.
During reset, all bits are configured
as inputs. When used as a serial bus
interface input/output, the latch must
be set to “1”.
8-bit programmable input/output
port. Each bit of these ports can be
individually configured as an input or
an output under software control.
During reset, all bits are configured
as inputs.
8-bit programmable input/output
port. Each bit of these ports can be
individually configured as an input or
an output under software control.
During reset, all bits are configured
as inputs. When used as a serial bus
interface input/output, the latch must
be set to “1”.
8-bit programmable input/output
port. (P67 to 61: Tri-State, P60: High
current output) Each bit of these
ports can be individually configured
as an input or an output under
software control. During reset, all
bits are configured as inputs. When
used P64 to P67 as port, each bit of
the P6 port data selection register
(bit 7 to 4 in ORP6S) must be set to
“1”.
P63 to P61 output “0” after a reset.
When these dual-function pins are
used as ports, be sure to set
ORP6S2 to “1”.
88CS34-4
Function
External interrupt input 5 or STOP
mode release signal input
I
I
Video signal input 1 or Composite
sync input
External interrupt input 4 or
Timer/Counter input 3
External interrupt input 3 or Remote
control signal preprocessor input
12-bit DA conversion (PWM) outputs
14/12-bit DA conversion (PWM)
outputs
Key on wake-up inputs or AD
converter analog inputs
Key on wake-up input or AD
converter analog input or
Timer/counter input 1 or External
interrupt input 2 or SIO serial clock
input/output 1
I
SIO serial data output 1
I
SIO serial data input 1
Timer/Counter input 2 or External
interrupt input 0
Y or BL output
R/G/B outputs
R input
G input
Key on wake-up input 5 or B input or
AD converter analog input 5
Key on wake-up input 4 or Y/BL
input or AD converter analog input 4
Translucent signal output
2
2
2
2
C bus serial data input/output 0
C bus serial clock input/output 0
C bus serial data Input/Output 1 or
C bus serial data Input/Output 1 or
TMP88CS34CP34
2007-09-12