AT91SAM7A3-AU Atmel, AT91SAM7A3-AU Datasheet - Page 57

• Manufacturer Part Number: AT91SAM7A3-AU
• Description: IC ARM7 MCU FLASH 256K 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7A3-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 60MHz
• Connectivity: CAN, I²C, MMC, SPI, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Controller Family/series: AT91SAM7xx
• No. Of I/o's: 62
• Ram Memory Size: 32KB
• Cpu Speed: 60MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Package: 100LQFP
• Device Core: ARM7TDMI
• Family Name: 91S
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 62
• Interface Type: CAN/SPI/I2S/TWI/USART/USB
• On-chip Adc: 2(8-chx10-bit)
• Number Of Timers: 3
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Ram Size: 32 KB
• Maximum Clock Frequency: 60 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7A3-EK
• Minimum Operating Temperature: - 40 C
• Cpu Family: 91S
• Device Core Size: 32b
• Frequency (max): 60MHz
• Total Internal Ram Size: 32KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7A3-EK - KIT EVAL FOR AT91SAM7A3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Figure 14-5. User Reset State
14.3.3.4
6042E–ATARM–14-Dec-06
periph_nreset
proc_nreset
Software Reset
(nrst_out)
RSTTYP
NRST
SLCK
NRST
MCK
T h e N R S T M a n a g e r g u a r a n t e e s t h a t t h e N R S T l i n e i s a s s e r t e d f o r
EXTERNAL_RESET_LENGTH Slow Clock cycles, as programmed in the field ERSTL. How-
ever, if NRST does not rise after EXTERNAL_RESET_LENGTH because it is driven low
externally, the internal reset lines remain asserted until NRST actually rises.
The Reset Controller offers several commands used to assert the different reset signals.
These commands are performed by writing the Control Register (RSTC_CR) with the following
bits at 1:
The software reset is entered if at least one of these bits is set by the software. All these com-
mands can be performed independently or simultaneously. The software reset lasts 3 Slow
Clock cycles.
The internal reset signals are asserted as soon as the register write is performed. This is
detected on the Master Clock (MCK). They are released when the software reset is left, i.e.;
synchronously to SLCK.
If EXTRST is set, the nrst_out signal is asserted depending on the programming of the field
ERSTL. However, the resulting falling edge on NRST does not lead to a User Reset.
• PROCRST: Writing PROCRST at 1 resets the processor and the watchdog timer.
• PERRST: Writing PERRST at 1 resets all the embedded peripherals, including the memory
• EXTRST: Writing EXTRST at 1 asserts low the NRST pin during a time defined by the field
system, and, in particular, the Remap Command. The Peripheral Reset is generally used
for debug purposes.
ERSTL in the Mode Register (RSTC_MR).
Resynch.
2 cycles
Any
Freq.
Any
>= EXTERNAL RESET LENGTH
Resynch.
2 cycles
XXX
AT91SAM7A3 Preliminary
Processor Startup
= 3 cycles
0x4 = User Reset
57