AT91SAM7A3-AU Atmel, AT91SAM7A3-AU Datasheet - Page 578

• Manufacturer Part Number: AT91SAM7A3-AU
• Description: IC ARM7 MCU FLASH 256K 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7A3-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 60MHz
• Connectivity: CAN, I²C, MMC, SPI, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Controller Family/series: AT91SAM7xx
• No. Of I/o's: 62
• Ram Memory Size: 32KB
• Cpu Speed: 60MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Package: 100LQFP
• Device Core: ARM7TDMI
• Family Name: 91S
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 62
• Interface Type: CAN/SPI/I2S/TWI/USART/USB
• On-chip Adc: 2(8-chx10-bit)
• Number Of Timers: 3
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Ram Size: 32 KB
• Maximum Clock Frequency: 60 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7A3-EK
• Minimum Operating Temperature: - 40 C
• Cpu Family: 91S
• Device Core Size: 32b
• Frequency (max): 60MHz
• Total Internal Ram Size: 32KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7A3-EK - KIT EVAL FOR AT91SAM7A3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

40.2.8.4
40.2.8.5
40.2.9
40.2.9.1
40.2.9.2
40.2.10
40.2.10.1
578
AT91SAM7A3 Preliminary
Universal Synchronous Asynchronous Receiver Transmitter (USART)
VDDBU
TWI: Disabling Does not Operate Correctly
TWI: Software Reset
USART: Hardware Handshaking – Two Characters Sent
USART: XOFF Character Bad Behavior
VDDBU: Idd When Accessing the APB
The user must wait for the TXCOMP status bit by interrupt and must not read the TWI_SR as
long as transmission is not completed.
Note:
Any transfer in progress is immediately frozen if the Control Register (TWI_CR) is written with
the bit MSDIS at 1. Furthermore, the status bits TXCOMP and TXRDY in the Status Register
(TWI_SR) are not reset.
The user must wait for the end of transfer before disabling the TWI. In addition, the interrupts
must be disabled before disabling the TWI.
when a software reset is performed during a frame and when TWCK is low, it is impossible to ini-
tiate a new transfer in READ or WRITE mode.
None.
If CTS switches from 0 to 1 during the TX of a character and if the holding register (US_THR) is
not empty, the content of US_THR will also be transmitted.
Don't use the PDC in transmit mode and do not fill US_THR before TXEMPTY is set at 1.
The XOFF character is sent only when the receive buffer is detected full. While the XOFF is
being sent, the remote transmitter is still transmitting. As only one Holding register is available in
the receiver, characters will be lost in reception. This makes the software handshaking function-
ality ineffective.
None.
During access to APB (via any peripheral) the current consumption on VDDBU increases.
It typically adds 20 µA.
Minimize the APB access if the current consumption over VDDBU is a key point in the
application.
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
TXCOMP and NACK fields are set simultaneously and the NACK field is reset after the read of the
TWI_SR.
6042E–ATARM–14-Dec-06