AT91SAM9XE128-QU Atmel, AT91SAM9XE128-QU Datasheet - Page 569

• Manufacturer Part Number: AT91SAM9XE128-QU
• Description: MCU ARM9 128K FLASH 208-PQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9XE128-QU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-MQFP, 208-PQFP
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: 2-Wire, EBI, I2S, SPI, USART
• Maximum Clock Frequency: 180 MHz
• Number Of Programmable I/os: 96
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM9XE-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9XE-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• For Use With: AT91SAM9XE-EK - KIT EVAL FOR AT91SAM9XEAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

• CKG: Receive Clock Gating Selection
• START: Receive Start Selection
• STOP: Receive Stop Selection
0 = After completion of a data transfer when starting with a Compare 0, the receiver stops the data transfer and waits for a
new compare 0.
1 = After starting a receive with a Compare 0, the receiver operates in a continuous mode until a Compare 1 is detected.
• STTDLY: Receive Start Delay
If STTDLY is not 0, a delay of STTDLY clock cycles is inserted between the start event and the actual start of reception.
When the Receiver is programmed to start synchronously with the Transmitter, the delay is also applied.
Note: It is very important that STTDLY be set carefully. If STTDLY must be set, it should be done in relation to TAG
(Receive Sync Data) reception.
• PERIOD: Receive Period Divider Selection
This field selects the divider to apply to the selected Receive Clock in order to generate a new Frame Sync Signal. If 0, no
PERIOD signal is generated. If not 0, a PERIOD signal is generated each 2 x (PERIOD+1) Receive Clock.
6254C–ATARM–22-Jan-10
0x9-0xF
START
0x0
0x1
0x2
0x3
0x4
0x5
0x6
0x7
0x8
CKG
0x0
0x1
0x2
0x3
Continuous, as soon as the receiver is enabled, and immediately after the end of
transfer of the previous data.
Transmit start
Detection of a low level on RF signal
Detection of a high level on RF signal
Detection of a falling edge on RF signal
Detection of a rising edge on RF signal
Detection of any level change on RF signal
Detection of any edge on RF signal
Compare 0
Reserved
Receive Start
None, continuous clock
Receive Clock enabled only if RF Low
Receive Clock enabled only if RF High
Reserved
Receive Clock Gating
AT91SAM9XE128/256/512 Preliminary
569