AT90PWM216-16SUR Atmel, AT90PWM216-16SUR Datasheet - Page 52

• Manufacturer Part Number: AT90PWM216-16SUR
• Description: MCU AVR 16K FLASH 16MHZ 24SOIC
• Manufacturer: Atmel
• Series: AVR® 90PWM Lightingr

Specifications of AT90PWM216-16SUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 19
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 24-SOIC (7.5mm Width)
• Processor Series: AT90PWMx
• Core: AVR8
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRFBKIT, ATAVRISP2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.9.1
52
AT90PWM216/316
Watchdog Timer Control Register - WDTCSR
Note: If the Watchdog is accidentally enabled, for example by a runaway pointer or brown-out
condition, the device will be reset and the Watchdog Timer will stay enabled. If the code is not
set up to handle the Watchdog, this might lead to an eternal loop of time-out resets. To avoid this
situation, the application software should always clear the Watchdog System Reset Flag
(WDRF) and the WDE control bit in the initialisation routine, even if the Watchdog is not in use.
The following code example shows one assembly and one C function for changing the time-out
value of the Watchdog Timer.
Note:
Note: The Watchdog Timer should be reset before any change of the WDP bits, since a change
in the WDP bits can result in a time-out when switching to a shorter time-out period;
Bit
Read/Write
Assembly Code Example
C Code Example
TABLE 2.
WDT_Prescaler_Change:
void WDT_Prescaler_Change(void)
{
}
; Turn off global interrupt
cli
; Reset Watchdog Timer
wdr
; Start timed sequence
lds r16, WDTCSR
ori
sts WDTCSR, r16
; --
; Set new prescaler(time-out) value = 64K cycles (~0.5 s)
ldi
sts WDTCSR, r16
; --
; Turn on global interrupt
sei
ret
__disable_interrupt();
__watchdog_reset();
/* Start timed
WDTCSR |= (1<<WDCE) | (1<<WDE);
/* Set new prescaler(time-out) value = 64K cycles (~0.5 s) */
WDTCSR
__enable_interrupt();
1. The example code assumes that the part specific header file is included.
r16, (1<<WDCE) | (1<<WDE)
Got four cycles to set the new values from here -
r16, (1<<WDE) | (1<<WDP2) | (1<<WDP0)
Finished setting new values, used 2 cycles -
WDIF
R/W
= (1<<WDE) | (1<<WDP2) | (1<<WDP0);
7
(1)
WDIE
R/W
6
(1)
equence */
WDP3
R/W
5
WDCE
R/W
4
WDE
R/W
3
WDP2
R/W
2
WDP1
R/W
1
WDP0
R/W
0
7710E–AVR–08/10
WDTCSR