PIC16C781-I/P Microchip Technology, PIC16C781-I/P Datasheet - Page 91

• Manufacturer Part Number: PIC16C781-I/P
• Description: IC MCU OTP 1KX14 W/AD COMP 20DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C781-I/P

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x8b; D/A 1x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 16
• Ram Memory Size: 128Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Processor Series: PIC16C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000, DM163022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• On-chip Dac: 8 bit, 1 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMINGDVA16XP202 - ADAPTER DEVICE PIC16C781/782DM163012 - BOARD DEMO PICDEM FOR 16C781/782AC164028 - MODULE SKT PROMATEII 20SOIC/DIP
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC16C781I/P

12.0
The comparator module has two separate voltage com-
parators: Comparator C1 and Comparator C2 (see
Figure 12-1).
Each comparator offers the following list of features:
• Control and configuration register
• Comparator output available externally
• Programmable output polarity
• Interrupt-on-change flags
• Wake-up from SLEEP
• Configurable as feedback input to the PSMC
• Programmable four input multiplexer
• Programmable reference selections
• Programmable speed
• Output synchronization to Timer1 clock input
12.1
Both comparators have separate control and configura-
tion registers: CM1CON0 for C1 and CM2CON0 for C2.
In addition, Comparator C2 has a second control regis-
ter, CM2CON1, for synchronization control and simul-
taneous reading of both comparator outputs.
12.1.1
The CM1CON0 register (shown in Register 12-1) con-
tains the control and status bits for the following:
• Comparator enable
• Comparator input selection
• Comparator reference selection
• Output mode
• Comparator speed
Setting C1ON (CM1CON0<7>) enables Comparator
C1 for operation.
Bits C1CH<1:0> (CM1CON0<1:0>) select the compar-
ator input from the four analog pins AN<7:4>.
(Comparator C2 only)
Note:
2001 Microchip Technology Inc.
COMPARATOR MODULE
Control Registers
To use AN<7:4> as analog inputs, the
appropriate bits must be programmed in
the ANSEL register.
COMPARATOR C1 CONTROL
REGISTER
Preliminary
Setting C1R (CM1CON0<2>) selects the output of the
DAC module as the reference voltage for the compara-
tor. Clearing C1R selects the V
AN3/V
The output of the comparator is available internally via
the C1OUT flag (CM1CON0<6>). To make the output
available for an external connection, the C1OE flag
(CM1CON0<5>) must be set. If the module is disabled
with C1OE set, the output will be driven as shown in
Table 12-2:
The polarity of the comparator output can be inverted
by setting the C1POL flag (CM1CON0<4>). Clearing
C1POL results in a non-inverted output. A complete
table showing the output state versus input conditions
and the polarity bit is shown in Table 12-2.
TABLE 12-1:
C1SP (CM1CON0<3>) configures the speed of the
comparator. When C1SP is set, the comparator oper-
ates at its normal speed. Clearing C1SP operates the
comparator in a slower, low power mode.
Input Condition
Note 1: The internal output of the comparator is
C1VN > C1VP
C1VN < C1VP
C1VN > C1VP
C1VN < C1VP
REF
2: The C1 interrupt will operate correctly
3: For the output of C1 on RB6/C1/
1 pin.
latched at the end of each instruction
cycle. External outputs are not latched.
with C1OE set or cleared.
PSMC1A, the PSMC must be disabled
and TRISB<6> must be ‘0’.
PIC16C781/782
OUTPUT STATE VERSUS
INPUT CONDITIONS
C1POL
0
0
1
1
REF
1 input on the RA3/
DS41171A-page 89
C1OUT
0
1
1
0