UPD78F0513AMC-GAA-AX Renesas Electronics America, UPD78F0513AMC-GAA-AX Datasheet - Page 719

• Manufacturer Part Number: UPD78F0513AMC-GAA-AX
• Description: MCU 8BIT 38PIN SSOP
• Manufacturer: Renesas Electronics America
• Series: 78K0/Kx2r

Specifications of UPD78F0513AMC-GAA-AX

• Core Processor: 78K/0
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 31
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0/Kx2
R01UH0008EJ0401 Rev.4.01
Jul 15, 2010
Address: 0081H/1081H
Address: 0082H/1082H, 0083H/1083H
Address: 0084H/1084H
Notes 1.
Caution Be sure to clear bits 7 to 1 to “0”.
Note Be sure to set 00H to 0082H and 0083H, as these addresses are reserved areas. Also set 00H to 1082H and
Notes 1.
Remark For the on-chip debug security ID, see CHAPTER 28 ON-CHIP DEBUG FUNCTION (
1083H because 0082H and 0083H are switched with 1082H and 1083H when the boot swap operation is used.
2.
2.
78F05xxDA ONLY).
POCMODE
POCMODE can only be written by using a dedicated flash memory programmer. It cannot be set during
self-programming or boot swap operation during self-programming. However, because the value of 1081H
is copied to 0081H during the boot swap operation, it is recommended to set a value that is the same as
that of 0081H to 1081H when the boot swap function is used.
To change the setting for the POC mode, set the value to 0081H again after batch erasure (chip erasure) of
the flash memory. The setting cannot be changed after the memory of the specified block is erased.
Be sure to set 00H (on-chip debug operation disabled) to 0084H for products not equipped with the on-chip
debug function (
switched during the boot swap operation.
To use the on-chip debug function with a product equipped with the on-chip debug function (
and 78F05xxDA), set 02H or 03H to 0084H. Set a value that is the same as that of 0084H to 1084H
because 0084H and 1084H are switched during the boot swap operation.
OCDEN1
7
0
1
7
7
0
0
0
0
0
1
1
Notes 1, 2
Notes1, 2
1.59 V POC mode (default)
2.7 V/1.59 V POC mode
OCDEN0
6
0
6
0
6
0
0
1
0
1
μ
PD78F05xx and 78F05xxA). Also set 00H to 1084H because 0084H and 1084H are
Note
Figure 26-1. Format of Option Byte (2/2)
Operation disabled
Setting prohibited
Operation enabled. Does not erase data of the flash memory in case authentication
of the on-chip debug security ID fails.
Operation enabled. Erases data of the flash memory in case authentication of the
on-chip debug security ID fails.
5
0
5
0
5
0
4
0
4
0
4
0
POC mode selection
On-chip debug operation control
3
0
3
0
3
0
2
0
2
0
2
0
CHAPTER 26 OPTION BYTE
OCDEN1
1
0
1
0
1
μ
PD78F05xxD and
POCMODE
OCDEN0
μ
PD78F05xxD
0
0
0
0
719