AT91SAM7S64C-AU Atmel, AT91SAM7S64C-AU Datasheet - Page 703

• Manufacturer Part Number: AT91SAM7S64C-AU
• Description: IC ARM7 MCU 32BIT 64K 64LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7S64C-AU

• Package / Case: 64-LQFP
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Operating Temperature: -40°C ~ 85°C
• Speed: 55MHz
• Number Of I /o: 32
• Core Processor: ARM7
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Program Memory Size: 64KB (64K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Connectivity: I²C, SPI, SSC, UART/USART, USB
• Core Size: 16/32-Bit
• Core: ARM7TDMI
• Package: 64LQFP
• Device Core: ARM7TDMI
• Family Name: AT91
• Maximum Speed: 55 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 32
• Interface Type: SPI/TWI/USART/USB
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: AT91SAM7S64B-AU::AT91SAM7S64B-AU

40.16.6.7
40.16.6.8
40.16.6.9
40.16.6.10
40.16.6.11
40.16.6.12
6175K–ATARM–30-Aug-10
SPI: Baudrate Set to 1
SPI: Disable In Slave Mode
SPI: Disable Issue
SPI: Software Reset and SPIEN Bit
SPI: CSAAT = 1 and Delay
SPI: Bad Serial Clock Generation on 2nd Chip Select
transfer is performed in Fixed mode through the PDC, on Chip select 1, the transfer will be con-
sidered as a HalfWord transfer.
If a PDC transfer has to be performed in 8 bits, on a Chip select y (y as different from 0), the
BITS field of the SPI_CSR0 must be configured in 8 bits, in the same way as the BITS field of
the CSRy Register.
When Baudrate is set at 1 (i.e. when serial clock frequency equals the system clock frequency)
and when the BITS field of the SPI_CSR register (number of bits to be transmitted) equals an
ODD value (in this case 9,11,13 or 15), an additional pulse will be generated on output SPCK.
Everything is OK if the BITS field equals 8,10,12,14 or 16 and Baudrate = 1.
None.
The SPI disable is not possible in slave mode.
Read first the received data, then perform the software reset.
The SPI Command “SPI Disable” is not possible during a transfer, it must be performed only
after TX_EMPTY rising else there is everlasting dummy transfers occur.
None.
The SPI Command “software reset” does not reset the SPIEN config bit. Therefore rewriting an
SPI enable command does not set TX_READY, TX_EMPTY flags.
Send SPI disable command after a software reset.
If CSAAT = 1 for current access and there is no more TX request for a time greater
than DLYBCT + DLYBCS, then if an access is requested on another slave, the NPCS bus
switches from one CS to the one requested without DLYBCS. External Slaves may reach a con-
tention on SPI_MISO line for a short period.
Assert the Last Transfer Command (NPCS de-activation) for the last character of each slave.
Bad Serial clock generation on the 2nd chip select when SCBR = 1, CPOL = 1 and NCPHA = 0.
This occurs using SPI with the following conditions:
• Master Mode
• CPOL = 1 and NCPHA = 0
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
AT91SAM7S Series Preliminary
703