XR17V358IB176-F Exar Corporation, XR17V358IB176-F Datasheet - Page 46

• Manufacturer Part Number: XR17V358IB176-F
• Description: IC UART PCIE OCTAL 176FPBGA
• Manufacturer: Exar Corporation

Specifications of XR17V358IB176-F

• Number Of Channels: 1, UART
• Package / Case: 176-LFBGA
• Features: *
• Fifo's: 256 Byte
• Protocol: RS485
• Voltage - Supply: 1.2V, 3.3V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 25 Mbps
• Supply Current: 120 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3.3 V
• No. Of Channels: 8
• Uart Features: Tx/Rx FIFO Counters
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: BGA
• No. Of Pins: 176
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 1016-1296 - EVAL BOARD FOR XR17V358-E81016-1295 - EVAL BOARD FOR XR17V358-E41016-1293 - EVAL BOARD FOR XR17V358
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1016-1294

XR17V358
HIGH PERFORMANCE OCTAL PCI EXPRESS UART
REV. 1.0.2
3.7
Receiver
The receiver section contains an 8-bit Receive Shift Register (RSR) and Receive Holding Register (RHR). The
RSR uses the 16X, 8X or 4X clock for timing. It verifies and validates every bit on the incoming character in the
middle of each data bit. On the falling edge of a start or false start bit, an internal receiver counter starts
counting at the 16X, 8X or 4X clock rate. After 8 or 4 or 2 clocks the start bit period should be at the center of
the start bit. At this time the start bit is sampled and if it is still a logic 0 it is validated. Evaluating the start bit in
this manner prevents the receiver from assembling a false character. The rest of the data bits and stop bits are
sampled and validated in this same manner to prevent false framing. If there were any error(s), they are
reported in the LSR register bits [4:1]. Upon unloading the receive data byte from RHR, the receive FIFO
pointer is bumped and the error flags are immediately updated to reflect the status of the data byte in RHR
register. RHR can generate a receive data ready interrupt upon receiving a character or delay until it reaches
the FIFO trigger level. Furthermore, data delivery to the host is guaranteed by a receive data ready time-out
function when receive data does not reach the receive FIFO trigger level. This time-out delay is 4 word lengths
as defined by LCR bits [1:0] plus 12 bits time. The RHR interrupt is enabled by IER bit [0].
3.7.1
Receiver Operation in non-FIFO Mode
F
15. R
O
-FIFO M
IGURE
ECEIVER
PERATION IN NON
ODE
16X or 8X or 4X
Clock
Receive Data Shift
Data Bit
Register (RSR)
Validation
Receive Data Characters
Error
Receive
Receive Data
Flags in
Data Byte
RHR Interrupt (ISR bit-2)
Holding Register
LSR bits
and Errors
(RHR)
4:2
46