KSZ8893MBLI Micrel Inc, KSZ8893MBLI Datasheet - Page 13

• Manufacturer Part Number: KSZ8893MBLI
• Description: 2+1 Port 10/100 Switch W/ Tranceivers & Frame Buffers ( )
• Manufacturer: Micrel Inc

Specifications of KSZ8893MBLI

• Controller Type: Ethernet Switch Controller
• Interface: MII, RMII, SNI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LFBGA
• Number Of Primary Switch Ports: 3
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Power Supply Type: Analog/Digital
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Industrial
• Data Rate: 100Mbps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / RoHS Status: Not Compliant, Lead free / RoHS Compliant
• Other names: 576-3575

February 2010
Note:
1. P = Power supply.
Pin Number
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Gnd = Ground.
I = Input.
Ipu = Input w/ internal pull-up.
Ipd = Input w/ internal pull-down.
Opd = Output w/ internal pull-down.
Pin Name
RMII_EN
HWPOVR
P2MDIXDIS
P2MDIX
P1ANEN
P1SPD
P1DPX
P1FFC
NC
NC
PWRDN
AGND
VDDA
AGND
MUX1
MUX2
Type
Opd
Ipd
Ipd
Ipd
Ipu
Ipd
Ipd
Ipd
Ipd
Ipd
Ipu
Gnd
P
Gnd
I
I
(1)
13
Description
Strap pin for RMII Mode
0 = Disable
1 = Enable
After reset, this pin has no meaning and is a no connect.
Hardware pin overwrite
0 = Disable. All strap-in pins configurations are overwritten by
the EEPROM configuration data
1 = Enable. All strap-in pins configurations are overwritten by
the EEPROM configuration data, except for register 0x2C bits
[7:5], (port 2: auto-negotiation enable, force speed, force
duplex).
Port 2 Auto MDI/MDI-X
PD (default) = enable
PU = disable
Port 2 MDI/MDI-X setting when auto MDI/MDI-X is disabled.
PD (default) = MDI-X (transmit on TXP2 / TXM2 pins)
PU = MDI, (transmit on RXP2 / RXM2 pins)
1 = enable auto-negotiation on port 1
0 = disable auto-negotiation on port 1
1 = force port 1 to 100BT if P1ANEN = 0
0 = force port 1 to 10BT if P1ANEN = 0
1 = port 1 default to full duplex mode if P1ANEN = 1 and auto-
negotiation fails. Force port 1 in full-duplex mode if P1ANEN
= 0.
0 = port 1 default to half duplex mode if P1ANEN = 1 and
auto- negotiation fails. Force port 1 in half duplex mode if
P1ANEN = 0.
1 = always enable (force) port 1 flow control feature
0 = port 1 flow control feature enable is determined by auto
negotiation result.
No connect
No connect
Chip power down input (active low)
Analog ground
1.2V analog V
Analog ground
Factory test pin - float for normal operation
Factory test pin - float for normal operation
DD
M9999-021110-1.6