KSZ8893MBLI Micrel Inc, KSZ8893MBLI Datasheet - Page 81

• Manufacturer Part Number: KSZ8893MBLI
• Description: 2+1 Port 10/100 Switch W/ Tranceivers & Frame Buffers ( )
• Manufacturer: Micrel Inc

Specifications of KSZ8893MBLI

• Controller Type: Ethernet Switch Controller
• Interface: MII, RMII, SNI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LFBGA
• Number Of Primary Switch Ports: 3
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Power Supply Type: Analog/Digital
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Industrial
• Data Rate: 100Mbps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / RoHS Status: Not Compliant, Lead free / RoHS Compliant
• Other names: 576-3575

Register 31 (0x1F): Port 1 Status 1 (continued)
Register 47 (0x2F): Port 2 Status 1 (continued)
Register 63 (0x3F): Port 3 Status 1 (continued)
Advanced Control Registers
The IPv4/IPv6 TOS Priority Control Registers implement a fully decoded, 128-bit DSCP (Differentiated Services
Code Point) register set that is used to determine priority from the ToS (Type of Service) field in the IP header.
The most significant 6 bits of the ToS field are fully decoded into 64 possibilities, and the singular code that
results is compared against the corresponding bits in the DSCP register to determine the priority.
Register 96 (0x60): TOS Priority Control Register 0
Bit
2
1
0
Bit
7-6
5-4
3-2
1-0
February 2010
Name
Operation
Speed
Operation
Duplex
Far-end Fault
Name
DSCP[7:6]
DSCP[5:4]
DSCP[3:2]
DSCP[1:0]
R/W
RO
RO
RO
R/W
R/W
R/W
R/W
R/W
Description
1 = link speed is 100Mbps
0 = link speed is 10Mbps
1 = link duplex is full
0 = link duplex is half
= 1, Far-end fault status detected
= 0, no Far-end fault status detected
Description
The value in this field is used as the frame’s
priority when bits [7:2] of the frame’s IP
TOS/DiffServ/Traffic Class value is 0x0C.
The value in this field is used as the frame’s
priority when bits [7:2] of the frame’s IP
TOS/DiffServ/Traffic Class value is 0x08.
The value in this field is used as the frame’s
priority when bits [7:2] of the frame’s IP
TOS/DiffServ/Traffic Class value is 0x04.
The value in this field is used as the frame’s
priority when bits [7:2] of the frame’s IP
TOS/DiffServ/Traffic Class value is 0x00.
81
Default
0
0
0
Note: Only port
1 supports fiber.
This bit is
applicable to
port 1 only.
Default
00
00
00
00
M9999-021110-1.6