KSZ8893MBLI Micrel Inc, KSZ8893MBLI Datasheet - Page 79

• Manufacturer Part Number: KSZ8893MBLI
• Description: 2+1 Port 10/100 Switch W/ Tranceivers & Frame Buffers ( )
• Manufacturer: Micrel Inc

Specifications of KSZ8893MBLI

• Controller Type: Ethernet Switch Controller
• Interface: MII, RMII, SNI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LFBGA
• Number Of Primary Switch Ports: 3
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Power Supply Type: Analog/Digital
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Industrial
• Data Rate: 100Mbps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / RoHS Status: Not Compliant, Lead free / RoHS Compliant
• Other names: 576-3575

Register 29 (0x1D): Port 1 Control 13
Register 45 (0x2D): Port 2 Control 13
Register 61 (0x3D): Reserved, not applied to port 3
Bit
7
6
5
4
3
2
1
0
February 2010
Name
LED Off
Txdis
Restart AN
Disable Far-
end Fault
Power Down
Disable Auto
MDI/MDI-X
Force MDI
Loopback
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Description
= 1, turn off all port’s LEDs (LEDx_3, LEDx_2,
LEDx_1, LEDx_0, where “x” is the port number).
These pins will be driven high if this bit is set to
one.
= 0, normal operation
= 1, disable the port’s transmitter
= 0, normal operation
= 1, restart auto-negotiation
= 0, normal operation
= 1, disable far-end fault detection and pattern
transmission.
= 0, enable far-end fault detection and pattern
transmission
= 1, power down
= 0, normal operation
= 1, disable auto MDI/MDI-X function
= 0, enable auto MDI/MDI-X function
If auto MDI/MDI-X is disabled,
= 1, force PHY into MDI mode (transmit on
RXP/RXM pins)
=
TXP/TXM pins)
= 1, perform loopback, as indicated:
= 0, normal operation
0, force PHY into MDI-X mode (transmit on
Port 1 Loopback (reg. 29, bit 0 = ‘1’)
Port 2 Loopback (reg. 45, bit 0 = ‘1’)
Start: RXP2/RXM2 (port 2)
Loopback: PMD/PMA of port 1’s PHY
End: TXP2/TXM2 (port 2)
Start: RXP1/RXM1 (port 1)
Loopback: PMD/PMA of port 2’s PHY
End: TXP1/TXM1 (port 1)
79
Default
0
0
0
0
Note: Only port 1
supports fiber.
This bit is
applicable to port
1 only.
0
0
For port 2,
P2MDIXDIS pin
value during
reset.
0
For port 2,
P2MDIX pin value
during reset.
0
M9999-021110-1.6