KSZ8893MBLI Micrel Inc, KSZ8893MBLI Datasheet - Page 2

• Manufacturer Part Number: KSZ8893MBLI
• Description: 2+1 Port 10/100 Switch W/ Tranceivers & Frame Buffers ( )
• Manufacturer: Micrel Inc

Specifications of KSZ8893MBLI

• Controller Type: Ethernet Switch Controller
• Interface: MII, RMII, SNI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LFBGA
• Number Of Primary Switch Ports: 3
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Power Supply Type: Analog/Digital
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Industrial
• Data Rate: 100Mbps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / RoHS Status: Not Compliant, Lead free / RoHS Compliant
• Other names: 576-3575

Features
• Proven Integrated 3-Port 10/100 Ethernet Switch
• Comprehensive Configuration Register Access
• QoS/CoS Packet Prioritization Support
• Advanced Switch Features
• Low Latency Support
February 2010
– Special tagging mode to inform the processor which
ingress port receives the packet
– 3rd generation switch with three MACs and two
PHYs fully compliant with IEEE 802.3u standard
– Re-mapping of 802.1p priority field per port basis
– Four priority levels
– MAC filtering function to forward unknown unicast
– Double-tagging support
–
– Non-blocking switch fabric assures fast packet
delivery by utilizing an 1K MAC address lookup table
and a store-and-forward architecture
– Full duplex IEEE 802.3x flow control (PAUSE) with
force mode option
– Half-duplex back pressure flow control
– HP Auto MDI-X for reliable detection of and correction
for straight-through and crossover cables with disable
and enable option
– Micrel LinkMD
identification of faulty copper cabling
– 100BASE-FX support on port 1
– MII interface supports both MAC mode and PHY
mode
– RMII interface support with external 50MHz system
clock
– 7-wire serial network interface (SNI) support for
– Comprehensive LED Indicator support for link,
activity, full/half duplex and 10/100 speed
– Serial management interface (SMI) to all internal
registers
– MII management (MIIM) interface to PHY registers
– SPI and I
– I/0 pins strapping and EEPROM to program selective
registers in unmanaged switch mode
– Control registers configurable on the fly (port-priority,
802.1p/d/q, AN…)
– Per port, 802.1p and DiffServ-based
– IEEE 802.1q VLAN support for up to 16 groups (full-
range of VLAN IDs)
– VLAN ID tag/untag options, per port basis
– IEEE 802.1p/q tag insertion or removal on a per port
basis (egress)
– Programmable rate limiting at the ingress and egress
on a per port basis
– Broadcast storm protection with % control (global and
per port basis)
– IEEE 802.1d spanning tree protocol support
– IGMP snooping (Ipv4) and MLD snooping (Ipv6)
support for multicast packet filtering
– Repeater mode
legacy MAC
Support IEEE 802.1w, 802.1t spanning tree
packets to specified port
2
C Interface to all internal registers
TM
TDR-based cable diagnostics permit
2
• Switch Monitoring Features
• Low Power Dissipation:
• Industrial Temperature Range: –40
• Available in 128-Pin PQFP and 100-ball LFBGA,
Applications
• Typical
• Upgradeable
• Industrial
Note:
1. Reduces cost and time of PCB re-spin.
Lead- free package
– Port mirroring/monitoring/sniffing: ingress and/or
egress traffic to any port or MII
– MIB counters for fully compliant statistics gathering,
34 MIB counters per port
– Loopback modes for remote diagnostic of failure
– Full-chip hardware power-down (register configuration
not saved)
– Per port based software power-save on PHY (idle link
detection, register configuration preserved)
– Media Converter
– FTTx customer premises equipment
– VoIP Phone
– SOHO Residential Gateway
– Broadband Gateway / Firewall / VPN
– Integrated DSL/Cable Modem
– Wireless LAN access point + gateway
– Set-top/Game Box
– Standalone 10/100 switch
– Unmanaged switch with future option to migrate to a
managed solution
– Single PHY alternative with future expansion option
for two ports
– Applications requiring port redundancy and port
monitoring
– Sensor devices in redundant ring topology
– Voltages: Single power supply: 3.3V
(1)
M9999-021110-1.6
o
C to +85
o
C