LAN9311-NZW Standard Microsystems (SMSC), LAN9311-NZW Datasheet - Page 304

• Manufacturer Part Number: LAN9311-NZW
• Manufacturer: Standard Microsystems (SMSC)

Specifications of LAN9311-NZW

• Number Of Primary Switch Ports: 2
• Internal Memory Buffer Size: 32
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: No
• Integrated Led Drivers: Yes
• Phy/transceiver Interface: MII
• Power Supply Type: Analog
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Pin Count: 128
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Operating Temperature Classification: Commercial
• Data Rate: 100Mbps
• Lead Free Status / RoHS Status: Compliant

Revision 1.7 (06-29-10)
14.4.2.10
BITS
9:5
3:0
15
14
13
12
11
10
4
Auto-MDIX Control (AMDIXCTRL)
This bit is responsible for determining the source of Auto-MDIX control for
Port x. When set, the Manual MDIX and Auto MDIX straps
(manual_mdix_strap_1/auto_mdix_strap_1 for Port 1 PHY,
manual_mdix_strap_2/auto_mdix_strap_2 for Port 2 PHY) are overridden,
and Auto-MDIX functions are controlled using bit 14 (AMDIXEN) and bit 13
(AMDIXSTATE) of this register. When cleared, Auto-MDIX functionality is
controlled by the Manual MDIX and Auto MDIX straps by default. Refer to
Section 4.2.4, "Configuration Straps," on page 40
definitions.
0: Port x Auto-MDIX determined by strap inputs
1: Port x Auto-MDIX determined by bits 14 and 13
Auto-MDIX Enable (AMDIXEN)
When bit 15 (AMDIXCTRL) of this register is set, this bit is used in
conjunction with bit 13 (Auto-MDIX State) to control the Port x Auto-MDIX
functionality as shown in
Auto-MDIX State (AMDIXSTATE)
When bit 15 (AMDIXCTRL) of this register is set, this bit is used in
conjunction with bit 14 (Auto-MDIX Enable) to control the Port x Auto-MDIX
functionality as shown in
RESERVED
SQE Test Disable (SQEOFF)
This bit controls the disabling of the SQE test (Heartbeat). SQE test is
enabled by default.
0: SQE test enabled
1: SQE test disabled
Receive PLL Lock Control (VCOOFF_LP)
This bit controls the locking of the receive PLL. Setting this bit to 1 forces
the receive PLL 10M to lock on the reference clock at all times. When in this
mode, 10M data packets cannot be received.
0: Receive PLL 10M can lock on reference or line as needed (normal
operation)
1: Receive PLL 10M locked onto reference clock at all times
RESERVED
10Base-T Polarity State (XPOL)
This bit shows the polarity state of the 10Base-T.
0: Normal Polarity
1: Reversed Polarity
RESERVED
Port x PHY Special Control/Status Indication Register (PHY_SPECIAL_CONTROL_STAT_IND_x)
This read/write register is used to control various options of the Port x PHY.
Note 14.61 Register bits designated as NASR are reset when the Port x PHY Reset is generated via
Index (decimal): 27
the
t h e
(PHY_BASIC_CONTROL_x)
Reset Control Register
R e s e t ( P H Y _ R S T )
Table
Table
DESCRIPTION
14.11.
14.11.
DATASHEET
(RESET_CTL). The NASR designation is only applicable when
is set.
b i t o f t h e
304
Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
for configuration strap
Size:
P o r t x P H Y B a s i c C o n t r o l R e g i s t e r
16 bits
Note 14.61
Note 14.61
Note 14.61
Note 14.61
Note 14.61
NASR
NASR
NASR
NASR
NASR
TYPE
R/W
R/W
R/W
R/W
R/W
SMSC LAN9311/LAN9311i
RO
RO
RO
RO
DEFAULT
Datasheet
0b
0b
0b
0b
0b
0b
-
-
-