LAN9211-ABZJ SMSC, LAN9211-ABZJ Datasheet - Page 92

• Manufacturer Part Number: LAN9211-ABZJ
• Description: IC ETHERNET CTLR SGL CHIP 56-QFN
• Manufacturer: SMSC
• Type: Single Chip MAC and PHY Controllerr

Specifications of LAN9211-ABZJ

• Controller Type: Ethernet Controller
• Interface: Serial EEPROM
• Voltage - Supply: 3.3V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 56-QFN
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: IEEE 802.3 or IEEE 802.3u
• Data Rate: 10 Mbps or 100 Mbps
• Supply Voltage (max): 5 V
• Supply Voltage (min): 3.3 V
• Supply Current (max): 86 mA
• Maximum Operating Temperature: + 70 C
• Ethernet Connection Type: 100BASE-TX or 10BASE-T
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• No. Of Ports: 2
• Ethernet Type: IEEE 802.3 / 802.3u
• Interface Type: HBI
• Supply Current: 86mA
• Supply Voltage Range: 2.97V To 3.63V
• Operating Temperature Range: 0°C To +70°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1049-6

Revision 2.7 (03-15-10)
5.3.13
13-12
31:14
BITS
10
11
9
8
7
6
RESERVED
Power Management Mode (PM_MODE)
the appropriate Power Management mode. Special care must be taken when
modifying these bits.
Encoding:
00b – D0 (normal operation)
01b – D1 (wake-up frame and magic packet detection are enabled)
10b – D2 (can perform energy detect)
11b – RESERVED - Do not set in this mode
Note:
RESERVED
PHY Reset (PHY_RST) – Writing a ‘1’ to this bit resets the PHY. The internal
logic automatically holds the PHY reset for a minimum of 100us. When the
PHY is released from reset, this bit is automatically cleared. All writes to this
bit are ignored while this bit is high.
Wake-On-Lan Enable (WOL_EN) – When set, the PME signal (if enabled
with PME_EN) will be asserted in accordance with the PME_IND bit upon a
WOL event. When set, the PME_INT will also be asserted upon a WOL
event, regardless of the setting of the PME_EN bit.
Energy-Detect Enable (ED_EN) - When set, the PME signal (if enabled with
PME_EN) will be asserted in accordance with the PME_IND bit upon an
Energy-Detect event. When set, the PME_INT will also be asserted upon an
Energy Detect event, regardless of the setting of the PME_EN bit.
RESERVED
PME Buffer Type (PME_TYPE) – When cleared, enables PME to function
as an open-drain buffer for use in a Wired-Or configuration. When set, the
PME output is a Push-Pull driver. When configured as an open-drain output
the PME_POL field is ignored, and the output is always active low.
PMT_CTRL— Power Management Control Register
This register controls the Power Management features. This register can be read while the
LAN9211
Note: The LAN9211 must always be read at least once after power-up, reset, or upon return from a
Offset:
When the LAN9211 is in any of the reduced power modes, a write
of any data to the BYTE_TEST register will wake-up the device. DO
NOT PERFORM WRITES TO OTHER ADDRRESSES while the
READY bit in this register is cleared.
power-saving state or write operations will not function.
is in a power saving mode.
DESCRIPTION
84h
DATASHEET
High-Performance Small Form Factor Single-Chip Ethernet Controller with HP Auto-MDIX Support
–
These bits set the LAN9211 into
92
Size:
32 bits
NASR
TYPE
R/W
R/W
R/W
RO
RO
RO
SC
SC
SMSC LAN9211
DEFAULT
Datasheet
00b
0b
0b
0b
0b
-
-
-