PIC18F2455-I/SP Microchip Technology Inc., PIC18F2455-I/SP Datasheet - Page 164

• Manufacturer Part Number: PIC18F2455-I/SP
• Description: Microcontroller; 24 KB Flash; 2048 RAM; 256 EEPROM; 24 I/O; 28-Pin-SPDIP
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F2455-I/SP

• A/d Inputs: 10-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 12 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 23
• Interface: I2C/SPI/USART/USB
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin SPDIP
• Programmable Memory: 24K Bytes
• Ram Size: 2K Bytes
• Speed: 48 MHz
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC18F2450/4450
15.2
The Asynchronous mode of operation is selected by
clearing the SYNC bit (TXSTA<4>). In this mode, the
EUSART uses the standard Non-Return-to-Zero (NRZ)
format (one Start bit, eight or nine data bits and one
Stop bit). The most common data format is eight bits.
An on-chip dedicated 8-bit/16-bit Baud Rate Generator
can be used to derive standard baud rate frequencies
from the oscillator.
The EUSART transmits and receives the LSb first. The
EUSART’s transmitter and receiver are functionally
independent but use the same data format and baud
rate. The Baud Rate Generator produces a clock, either
x16 or x64 of the bit shift rate depending on the BRGH
and BRG16 bits (TXSTA<2> and BAUDCON<3>). Parity
is not supported by the hardware but can be
implemented in software and stored as the ninth data bit.
When operating in Asynchronous mode, the EUSART
module consists of the following important elements:
• Baud Rate Generator
• Sampling Circuit
• Asynchronous Transmitter
• Asynchronous Receiver
• Auto-Wake-up on Sync Break Character
• 12-Bit Break Character Transmit
• Auto-Baud Rate Detection
15.2.1
The EUSART transmitter block diagram is shown in
Figure 15-3. The heart of the transmitter is the Transmit
(Serial) Shift Register (TSR). The Shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREG. The TXREG register is loaded with data in
software. The TSR register is not loaded until the Stop
bit has been transmitted from the previous load. As
soon as the Stop bit is transmitted, the TSR is loaded
with new data from the TXREG register (if available).
FIGURE 15-3:
DS39760A-page 162
EUSART Asynchronous Mode
BRG16
EUSART ASYNCHRONOUS
TRANSMITTER
TXIE
Interrupt
EUSART TRANSMIT BLOCK DIAGRAM
SPBRGH
Baud Rate Generator
TXIF
TXEN
Baud Rate CLK
SPBRG
MSb
(8)
Advance Information
TXREG Register
TSR Register
TX9D
TX9
8
Data Bus
Once the TXREG register transfers the data to the TSR
register (occurs in one T
and the TXIF flag bit (PIR1<4>) is set. This interrupt can
be enabled or disabled by setting or clearing the interrupt
enable bit, TXIE (PIE1<4>). TXIF will be set regardless of
the state of TXIE; it cannot be cleared in software. TXIF
is also not cleared immediately upon loading TXREG but
becomes valid in the second instruction cycle following
the load instruction. Polling TXIF immediately following a
load of TXREG will return invalid results.
While TXIF indicates the status of the TXREG register,
another bit, TRMT (TXSTA<1>), shows the status of
the TSR register. TRMT is a read-only bit which is set
when the TSR register is empty. No interrupt logic is
tied to this bit so the user has to poll this bit in order to
determine if the TSR register is empty.
To set up an Asynchronous Transmission:
1.
2.
3.
4.
5.
6.
7.
8.
Note 1: The TSR register is not mapped in data
Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRGH
and BRG16 bits, as required, to achieve the
desired baud rate.
Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
If interrupts are desired, set enable bit TXIE.
If 9-bit transmission is desired, set transmit bit
TX9. Can be used as address/data bit.
Enable the transmission by setting bit TXEN
which will also set bit TXIF.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Load data to the TXREG register (starts
transmission).
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
LSb
2: Flag bit TXIF is set when enable bit TXEN
0
memory so it is not available to the user.
is set.
TRMT
and Control
Pin Buffer
CY
© 2006 Microchip Technology Inc.
), the TXREG register is empty
SPEN
TX pin