ATmega406 Atmel Corporation, ATmega406 Datasheet - Page 58

• Manufacturer Part Number: ATmega406
• Manufacturer: Atmel Corporation

Specifications of ATmega406

• Flash (kbytes): 40 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 1 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 18
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1.9
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -30 to 85
• I/o Supply Class: 4.0 to 25
• Operating Voltage (vcc): 4.0 to 25
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Pwm Channels: 2
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

12.2.4
12.2.5
58
ATmega406
PCICR– Pin Change Interrupt Control Register
PCIFR – Pin Change Interrupt Flag Register
set (one), the MCU will jump to the interrupt vector. The flag is cleared when the interrupt routine
is executed. Alternatively, the flag can be cleared by writing a logical one to it. These flags are
always cleared when INT3:0 are configured as level interrupt. Note that when entering sleep
mode with the INT3:0 interrupts disabled, the input buffers on these pins will be disabled. This
may cause a logic change in internal signals which will set the INTF3:0 flags. See
Enable and Sleep Modes” on page 64
• Bit 7:2 - Res: Reserved Bits
These bits are reserved bits in the ATmega406, and will always read as zero.
• Bit 1 - PCIE1: Pin Change Interrupt Enable 1
When the PCIE1 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin
change interrupt 1 is enabled. Any change on any enabled PCINT15:8 pin will cause an inter-
rupt. The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI1
Interrupt Vector. PCINT15:8 pins are enabled individually by the PCMSK1 Register.
• Bit 0 - PCIE0: Pin Change Interrupt Enable 0
When the PCIE0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin
change interrupt 0 is enabled. Any change on any enabled PCINT7:0 pin will cause an interrupt.
The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI0 Inter-
rupt Vector. PCINT7:0 pins are enabled individually by the PCMSK0 Register.
• Bit 7:2 - Res: Reserved Bits
These bits are reserved bits in the ATmega406, and will always read as zero.
• Bit 1 - PCIF1: Pin Change Interrupt Flag 1
When a logic change on any PCINT15:8 pin triggers an interrupt request, PCIF1 becomes set
(one). If the I-bit in SREG and the PCIE1 bit in PCICR are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 0 - PCIF0: Pin Change Interrupt Flag 0
When a logic change on any PCINT7:0 pin triggers an interrupt request, PCIF0 becomes set
(one). If the I-bit in SREG and the PCIE0 bit in PCICR are set (one), the MCU will jump to the
Bit
(0x68)
Read/Write
Initial Value
Bit
0x1B (0x3B)
Read/Write
Initial Value
R
R
7
–
0
7
–
0
R
R
6
–
0
6
–
0
R
R
5
–
0
5
–
0
for more information.
R
R
4
–
0
4
–
0
R
R
3
–
0
3
–
0
2
–
R
0
2
–
R
0
PCIE1
PCIF1
R/W
R/W
1
0
1
0
PCIE0
PCIF0
R/W
R/W
0
0
0
0
2548E–AVR–07/06
”Digital Input
PCICR
PCIFR