ATmega8 Atmel Corporation, ATmega8 Datasheet - Page 93

• Manufacturer Part Number: ATmega8
• Manufacturer: Atmel Corporation

Specifications of ATmega8

• Flash (kbytes): 8 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 2
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

2486Z–AVR–02/11
Figure 40. Phase and Frequency Correct PWM Mode, Timing Diagram
The Timer/Counter Overflow Flag (TOV1) is set at the same timer clock cycle as the OCR1x
Registers are updated with the double buffer value (at BOTTOM). When either OCR1A or ICR1
is used for defining the TOP value, the OC1A or ICF1 Flag set when TCNT1 has reached TOP.
The Interrupt Flags can then be used to generate an interrupt each time the counter reaches the
TOP or BOTTOM value.
When changing the TOP value the program must ensure that the new TOP value is higher or
equal to the value of all of the Compare Registers. If the TOP value is lower than any of the
Compare Registers, a Compare Match will never occur between the TCNT1 and the OCR1x.
As
in all periods. Since the OCR1x Registers are updated at BOTTOM, the length of the rising and
the falling slopes will always be equal. This gives symmetrical output pulses and is therefore fre-
quency correct.
Using the ICR1 Register for defining TOP works well when using fixed TOP values. By using
ICR1, the OCR1A Register is free to be used for generating a PWM output on OC1A. However,
if the base PWM frequency is actively changed by changing the TOP value, using the OCR1A as
TOP is clearly a better choice due to its double buffer feature.
In phase and frequency correct PWM mode, the compare units allow generation of PWM wave-
forms on the OC1x pins. Setting the COM1x1:0 bits to 2 will produce a non-inverted PWM and
an inverted PWM output can be generated by setting the COM1x1:0 to 3. See
97. The actual OC1x value will only be visible on the port pin if the data direction for the port pin
is set as output (DDR_OC1x). The PWM waveform is generated by setting (or clearing) the
OC1x Register at the Compare Match between OCR1x and TCNT1 when the counter incre-
ments, and clearing (or setting) the OC1x Register at Compare Match between OCR1x and
TCNT1 when the counter decrements. The PWM frequency for the output when using phase
and frequency correct PWM can be calculated by the following equation:
The N variable represents the prescaler divider (1, 8, 64, 256, or 1024).
The extreme values for the OCR1x Register represents special cases when generating a PWM
waveform output in the phase correct PWM mode. If the OCR1x is set equal to BOTTOM the
Figure 40
TCNTn
OCnx
OCnx
Period
shows the output generated is, in contrast to the Phase Correct mode, symmetrical
1
f
OCnxPFCPWM
2
3
=
--------------------------- -
2 N TOP
⋅
f
clk_I/O
⋅
4
(COMnx1:0 = 2)
(COMnx1:0 = 3)
OCnA Interrupt Flag Set or
ICFn Interrupt Flag Set
(Interrupt on TOP)
ATmega8(L)
OCRnx / TOP Update and
TOVn Interrupt Flag Set
(Interrupt on Bottom)
Table 38 on page
93