n25q032 Numonyx, n25q032 Datasheet - Page 139

no-image

n25q032

Manufacturer Part Number
n25q032
Description
32-mbit 3 V, Multiple I/o, 4-kbyte Subsector Erase, Xip Enabled, Serial Flash Memory With 108 Mhz Spi Bus Interface
Manufacturer
Numonyx
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
n25q03213
Manufacturer:
ST
0
Part Number:
n25q03213E40
Manufacturer:
MICRON
Quantity:
20 000
Part Number:
n25q032A11EF440E
Manufacturer:
MICRON/美光
Quantity:
20 000
Part Number:
n25q032A11EF640E
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Part Number:
n25q032A11EF640E
Manufacturer:
MICRON/美光
Quantity:
20 000
Part Number:
n25q032A11EF640F
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Part Number:
n25q032A11EF640F
Manufacturer:
MICRON
Quantity:
20 000
Company:
Part Number:
n25q032A11EF640F
Quantity:
20 000
Part Number:
n25q032A11ESE40
Manufacturer:
ST
0
Part Number:
n25q032A11ESE40F
Manufacturer:
ST
0
Part Number:
n25q032A11ESE40F
Manufacturer:
MICRON/美光
Quantity:
20 000
Part Number:
n25q032A13E1240E
Manufacturer:
MICRON
Quantity:
210
Part Number:
n25q032A13E1240F
Manufacturer:
MICRON
Quantity:
210
Company:
Part Number:
n25q032A13E1240F
Quantity:
110
Part Number:
n25q032A13E1241E
Manufacturer:
MICRON
Quantity:
5 000
11
Power-up and power-down
At power-up and power-down, the device must not be selected (that is Chip Select (S) must
follow the voltage applied on VCC) until VCC reaches the correct value:
A safe configuration is provided in
To avoid data corruption and inadvertent write operations during power-up, a Power On
Reset (POR) circuit is included. The logic inside the device is held reset while VCC is less
than the Power On Reset (POR) threshold voltage, VWI - all operations are disabled, and
the device does not respond to any instruction.
During a standard power-up phase the device ignores all the instructions but RDSR and
RFSR (they can be used to check the memory internal state according to
Power-up
After power-up, the device is in the following state:
Normal precautions must be taken for supply line decoupling, to stabilize the VCC supply.
Each device in a system should have the VCC line decoupled by a suitable capacitor close
to the package pins (generally, this capacitor is of the order of 100 nF).
At power-down, when VCC drops from the operating voltage, to below the Power On Reset
(POR) threshold voltage, VWI, all operations are disabled and the device does not respond
to any instruction (the designer needs to be aware that if power-down occurs while a Write,
Program or Erase cycle is in progress, some data corruption may result).
VPPH must be applied only when VCC is stable and in the VCC(min) to VCC(max) voltage
range.
Figure 102. Power-up timing
V
V
CC
CC
VCC(min) at power-up
VSS at power-down
The device is in the Standby Power mode
The Write Enable Latch (WEL) bit is reset
The Write In Progress (WIP) bit is reset
The Lock Registers are configured as: (Write Lock bit, Lock Down bit) = (0,0).
(max)
(min)
V
Vcc
WI
timing.
Chip
reset
Chip selection not allowed
Section 3: SPI
t
VTW
Polling allowed
SPI protocol
WIP = 1
WEL = 0
= t
Modes.
VTR
Starting protocol defined by NVCR
Device fully accessible
WIP = 0
WEL = 0
Figure 102.:
time
139/160

Related parts for n25q032