at32uc3b0512-z2ues ATMEL Corporation, at32uc3b0512-z2ues Datasheet - Page 440
at32uc3b0512-z2ues
Manufacturer Part Number
at32uc3b0512-z2ues
Description
32-bit Avr Microcontroller
Manufacturer
ATMEL Corporation
Datasheet
1.AT32UC3B0512-Z2UES.pdf
(680 pages)
- Current page: 440 of 680
- Download datasheet (10Mb)
•
•
•
•
32059J–12/2010
CURRBK: Current Bank
NBUSYBK: Number of Busy Banks
DTSEQ: Data Toggle Sequence
SHORTPACKET: Short Packet Interrupt
This bit is set for non-control endpoints, to indicate the current bank:
This field may be updated one clock cycle after the RWALL bit changes, so the user should not poll this field as an interrupt bit.
This field is set to indicate the number of busy banks:
For IN endpoints, it indicates the number of banks filled by the user and ready for IN transfer. When all banks are free, this
For OUT endpoints, it indicates the number of banks filled by OUT transactions from the host. When all banks are busy, this
When the FIFOCON bit is cleared (by writing a one to the FIFOCONC bit) to validate a new bank, this field is updated two or
An EPnINT interrupt is triggered if:
- for IN endpoint, NBUSYBKE is one and all the banks are free.
- for OUT endpoint, NBUSYBKE is one and all the banks are busy.
This field is set to indicate the PID of the current bank:
For IN transfers, it indicates the data toggle sequence that will be used for the next packet to be sent. This is not relative to the
For OUT transfers, this value indicates the last data toggle sequence received on the current bank.
By default DTSEQ is 0b01, as if the last data toggle sequence was Data1, so the next sent or expected data toggle sequence
This bit is set for non-control OUT endpoints, when a short packet has been received.
This bit is set for non-control IN endpoints, a short packet is transmitted upon ending a DMA transfer, thus signaling an end of
This triggers an EPnINT interrupt if SHORTPACKETE is one.
This bit is cleared when the SHORTPACKETC bit is written to one. This will acknowledge the interrupt.
0
0
1
1
0
0
1
1
0
0
1
triggers an EPnINT interrupt if NBUSYBKE is one.
triggers an EPnINT interrupt if NBUSYBKE is one.
three clock cycles later to calculate the address of the next bank.
current bank.
should be Data0.
isochronous frame or a bulk or interrupt end of transfer, this only if the End of DMA Buffer Output Enable (DMAENDEN) bit
and the Automatic Switch (AUTOSW) bit are written to one.
NBUSYBK
CURRBK
DTSEQ
X
0
1
0
1
0
1
0
1
0
1
Current Bank
Bank0
Bank1
Bank2
Reserved
Number of Busy Banks
0 (all banks free)
1
2
3
Data Toggle Sequence
Data0
Data1
Reserved
AT32UC3B
440
Related parts for at32uc3b0512-z2ues
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: