CY7C63231A-PXC Cypress Semiconductor Corp, CY7C63231A-PXC Datasheet - Page 13

• Manufacturer Part Number: CY7C63231A-PXC
• Description: IC MCU 3K USB LS PERIPH 18-DIP
• Manufacturer: Cypress Semiconductor Corp
• Series: enCoRe™r

Specifications of CY7C63231A-PXC

• Applications: USB Microcontroller
• Core Processor: M8B
• Program Memory Type: OTP (3 kB)
• Controller Series: CY7C632xx
• Ram Size: 96 x 8
• Interface: USB
• Number Of I /o: 10
• Voltage - Supply: 3.5 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 18-DIP (0.300", 7.62mm)
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Processor Series: CY7C63xx
• Core: M8B
• Data Bus Width: 16 bit
• Program Memory Size: 3 KB
• Data Ram Size: 96 B
• Interface Type: PS2, USB
• Maximum Clock Frequency: 12 MHz
• Number Of Programmable I/os: 10
• Number Of Timers: 1
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant

Clocking
The chip can be clocked from either the internal on-chip clock, or from an oscillator based on an external resonator/crystal, as shown
in
Register,
Bit 7: Ext. Clock Resume Delay
Document #: 38-08028 Rev. *D
Figure
External Clock Resume Delay bit selects the delay time when
switching to the external oscillator from the internal oscillator
mode, or when waking from suspend mode with the external
oscillator enabled.
1 = 4 ms delay.
0 = 128 μs delay.
The delay gives the oscillator time to start up. The shorter time
is adequate for operation with ceramic resonators, while the
longer time is preferred for start-up with a crystal. (These
times do not include an initial oscillator start-up time which
depends on the resonating element. This time is typically
50–100 μs for ceramic resonators and 1–10 ms for crystals).
Note that this bit only selects the delay time for the external
clock mode. When waking from suspend mode with the inter-
nal oscillator (Bit 0 is LOW), the delay time is only 8 μs in
Read/Write
Bit Name
Reset
Bit #
2. No additional capacitance is included on chip at the XTALIN/OUT pins. Operation is controlled by the Clock Configuration
Figure
(to Microcontroller)
Clk2x (12 MHz)
Clk1x (6 MHz)
(to USB SIE)
3.
Ext. Clock
Resume
Ext Osc Enable
Delay
R/W
7
0
Internal Osc
Int Clk Output Disable
Port 2.1
R/W
Figure 3. Clock Configuration Register (Address 0xF8)
Wake-up Timer Adjust Bit [2:0]
6
0
Doubler
Clock
Figure 2. Clock Oscillator On-chip Circuit
R/W
5
0
R/W
4
0
Bit [6:4]: Wake-up Timer Adjust Bit [2:0]
addition to a delay of approximately 1 μs for the oscillator to
start.
The Wake-up Timer Adjust Bits are used to adjust the
Wake-up timer period.
If the Wake-up interrupt is enabled in the Global Interrupt En-
able Register, the microcontroller will generate wake-up inter-
rupts periodically. The frequency of these periodical wake-up
interrupts is adjusted by setting the Wake-up Timer Adjust Bit
[2:0], as described in Section . One common use of the
wake-up interrupts is to generate periodical wake-up events
during suspend mode to check for changes, such as looking
for movement in a mouse, while maintaining a low average
power.
Low-voltage
Disable
Port 2.2
Reset
R/W
3
0
Precision
Clocking
Enable
USB
R/W
2
0
CY7C63221/31A
Internal
Disable
Output
Clock
R/W
1
0
XTALOUT
XTALIN
Oscillator
Page 13 of 47
External
Enable
R/W
0
0
[+] Feedback