PIC18F65J11-I/PT Microchip Technology, PIC18F65J11-I/PT Datasheet - Page 100

• Manufacturer Part Number: PIC18F65J11-I/PT
• Description: IC PIC MCU FLASH 16KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F65J11-I/PT

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 51
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 52
• Ram Memory Size: 2048Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Interface: I2C, SPI, USART
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 52
• Interface Type: I2C/SPI/USART
• On-chip Adc: 12-chx10-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180018 - MODULE PLUG-IN 18F85J11AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F85J11 FAMILY
8.1
The operation of the interface is controlled by the
MEMCON register (Register 8-1). This register is
available in all Program Memory modes except Micro-
controller mode. In this mode, the register is disabled
and cannot be written to.
The EBDIS bit (MEMCON<7>) controls the operation
of the bus and related port functions. Clearing EBDIS
enables the interface and disables the I/O functions of
the ports, as well as any other functions multiplexed to
those pins. Setting the bit enables the I/O ports and
other functions, but allows the interface to override
everything else on the pins when an external memory
operation is required. By default, the external bus is
always enabled and disables all other I/O.
REGISTER 8-1:
DS39774D-page 100
bit 15
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5-4
bit 3-2
bit 1-0
EBDIS
R/W-0
External Memory Bus Control
EBDIS: External Bus Disable bit
1 = External bus is enabled when microcontroller accesses external memory; otherwise, all external
0 = External bus is always enabled, I/O ports are disabled
Unimplemented: Read as ‘0’
WAIT<1:0>: Table Reads and Writes Bus Cycle Wait Count bits
11 = Table reads and writes will wait 0 T
10 = Table reads and writes will wait 1 T
01 = Table reads and writes will wait 2 T
00 = Table reads and writes will wait 3 T
Unimplemented: Read as ‘0’
WM<1:0>: TBLWT Operation with 16-Bit Data Bus Width Select bits
1x = Word Write mode: TABLAT0 and TABLAT1 word output; WRH active when TABLAT1 written
01 = Byte Select mode: TABLAT data copied on both MSB and LSB; WRH and (UB or LB) will activate
00 = Byte Write mode: TABLAT data copied on both MSB and LSB; WRH or WRL will activate
bus drivers are mapped as I/O ports
U-0
—
MEMCON: EXTERNAL MEMORY BUS CONTROL REGISTER
W = Writable bit
‘1’ = Bit is set
WAIT1
R/W-0
WAIT0
R/W-0
CY
CY
CY
CY
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
The operation of the EBDIS bit is also influenced by the
Program Memory mode being used. This is discussed
in more detail in Section 8.5 “Program Memory
Modes and the External Memory Bus”.
The WAIT bits allow for the addition of Wait states to
external memory operations. The use of these bits is
discussed in Section 8.3 “Wait States”.
The WM bits select the particular operating mode used
when the bus is operating in 16-Bit Data Width mode.
These are discussed in more detail in Section 8.6
“16-Bit Data Width Modes”. These bits have no effect
when an 8-Bit Data Width mode is selected.
U-0
—
U-0
—
 2010 Microchip Technology Inc.
x = Bit is unknown
R/W-0
WM1
R/W-0
WM0
bit 8