PIC18F65J11-I/PT Microchip Technology, PIC18F65J11-I/PT Datasheet - Page 164

• Manufacturer Part Number: PIC18F65J11-I/PT
• Description: IC PIC MCU FLASH 16KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F65J11-I/PT

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 51
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 52
• Ram Memory Size: 2048Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Interface: I2C, SPI, USART
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 52
• Interface Type: I2C/SPI/USART
• On-chip Adc: 12-chx10-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180018 - MODULE PLUG-IN 18F85J11AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F85J11 FAMILY
14.2
Timer2 can also generate an optional device interrupt.
The Timer2 output signal (TMR2 to PR2 match) pro-
vides the input for the 4-bit output counter/postscaler.
This counter generates the TMR2 match interrupt flag
which is latched in TMR2IF (PIR1<1>). The interrupt is
enabled by setting the TMR2 Match Interrupt Enable
bit, TMR2IE (PIE1<1>).
A range of 16 postscale options (from 1:1 through 1:16
inclusive) can be selected with the postscaler control
bits, T2OUTPS<3:0> (T2CON<6:3>).
FIGURE 14-1:
TABLE 14-1:
DS39774D-page 164
INTCON GIE/GIEH PEIE/GIEL
PIR1
PIE1
IPR1
TMR2
T2CON
PR2
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Timer2 module.
Name
T2OUTPS<3:0>
T2CKPS<1:0>
F
OSC
Timer2 Interrupt
/4
Timer2 Register
Timer2 Period Register
PSPIE
PSPIP
PSPIF
Bit 7
—
REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER
T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1 T2CKPS0
TIMER2 BLOCK DIAGRAM
Internal Data Bus
1:1, 1:4, 1:16
ADIF
ADIE
ADIP
Bit 6
2
Prescaler
TMR0IE
RC1IE
RC1IP
RC1IF
Bit 5
4
TMR2
INT0IE
TX1IE
TX1IP
TX1IF
Bit 4
Reset
8
SSPIF
SSPIE
SSPIP
RBIE
Bit 3
14.3
The unscaled output of TMR2 is available primarily to
the CCP modules where it is used as a time base for
operations in PWM mode.
Timer2 can be optionally used as the shift clock source
for the MSSP module operating in SPI mode.
Additional information is provided in Section 17.0
“Master Synchronous Serial Port (MSSP) Module”.
Comparator
1:1 to 1:16
Postscaler
8
TMR2/PR2
Match
Timer2 Output
TMR0IF
Bit 2
—
—
—
TMR2IF
TMR2IE
TMR2IP
INT0IF
 2010 Microchip Technology Inc.
Bit 1
PR2
8
Set TMR2IF
TMR2 Output
(to PWM or MSSP)
TMR1IE
TMR1IP
TMR1IF
Bit 0
RBIF
on page
Values
Reset
57
59
59
59
58
58
58