PIC18F65J11-I/PT Microchip Technology, PIC18F65J11-I/PT Datasheet - Page 31

• Manufacturer Part Number: PIC18F65J11-I/PT
• Description: IC PIC MCU FLASH 16KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F65J11-I/PT

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 51
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 52
• Ram Memory Size: 2048Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Interface: I2C, SPI, USART
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 52
• Interface Type: I2C/SPI/USART
• On-chip Adc: 12-chx10-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180018 - MODULE PLUG-IN 18F85J11AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

2.0
2.1
Getting started with the PIC18F85J11 family family of
8-bit microcontrollers requires attention to a minimal
set of device pin connections before proceeding with
development.
The following pins must always be connected:
• All V
• All AV
• MCLR pin
• ENVREG (if implemented) and V
These pins must also be connected if they are being
used in the end application:
• PGC/PGD pins used for In-Circuit Serial
• OSCI and OSCO pins when an external oscillator
Additionally, the following pins may be required:
• V
The minimum mandatory connections are shown in
Figure 2-1.
 2010 Microchip Technology Inc.
(see Section 2.2 “Power Supply Pins”)
not the analog device features are used
(see Section 2.2 “Power Supply Pins”)
(see Section 2.3 “Master Clear (MCLR) Pin”)
(see Section 2.4 “Voltage Regulator Pins
(ENVREG and V
Programming™ (ICSP™) and debugging purposes
(see Section 2.5 “ICSP Pins”)
source is used
(see Section 2.6 “External Oscillator Pins”)
reference for analog modules is implemented
Note:
REF
DD
+/V
DD
GUIDELINES FOR GETTING
STARTED WITH PIC18FJ
MICROCONTROLLERS
Basic Connection Requirements
and V
REF
and AV
The AV
connected, regardless of whether any of
the analog modules are being used.
- pins are used when external voltage
SS
SS
pins
DD
CAP
pins, regardless of whether or
and AV
/V
DDCORE
SS
pins must always be
)”)
CAP
/V
DDCORE
pins
PIC18F85J11 FAMILY
FIGURE 2-1:
V
Key (all values are recommendations):
C1 through C6: 0.1 F, 20V ceramic
C7: 10 F, 6.3V or greater, tantalum or ceramic
R1: 10 kΩ
R2: 100Ω to 470Ω
Note 1:
DD
C6
R1
C1
(2)
R2
2:
MCLR
See Section 2.4 “Voltage Regulator Pins
(ENVREG and V
explanation of ENVREG pin connections.
The example shown is for a PIC18F device
with five V
Other devices may have more or less pairs;
adjust the number of decoupling capacitors
appropriately.
V
V
SS
DD
C5
PIC18FXXJXX
RECOMMENDED
MINIMUM CONNECTIONS
(2)
DD
/V
SS
CAP
and AV
ENVREG
V
/V
CAP
DDCORE
C4
C2
/V
DD
DS39774D-page 31
DDCORE
(2)
(2)
/AV
V
V
DD
SS
)” for
SS
pairs.
(1)
C3
(1)
C7
(2)