MC908GP32CPE Freescale Semiconductor, MC908GP32CPE Datasheet - Page 219

• Manufacturer Part Number: MC908GP32CPE
• Description: IC MCU 8MHZ 32K FLASH 40-DIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GP32CPE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 33
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: HC08GP
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

18.2.2.3 SIM Break Status Register
The SIM break status register (SBSR) contains a flag to indicate that a break caused an exit from wait
mode. This register is only used in emulation mode.
SBSW — SIM Break Stop/Wait
18.2.2.4 SIM Break Flag Control Register
The SIM break control register (SBFCR) contains a bit that enables software to clear status bits while the
MCU is in a break state.
BCFE — Break Clear Flag Enable Bit
18.2.3 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power- consumption standby modes. If enabled,
the break module will remain enabled in wait and stop modes. However, since the internal address bus
does not increment in these modes, a break interrupt will never be triggered.
Freescale Semiconductor
SBSW can be read within the break state SWI routine. The user can modify the return address on the
stack by subtracting one from it.
This read/write bit enables software to clear status bits by accessing status registers while the MCU is
in a break state. To clear status bits during the break state, the BCFE bit must be set.
1 = Wait mode was exited by break interrupt
0 = Wait mode was not exited by break interrupt
1 = Status bits clearable during break
0 = Status bits not clearable during break
Address: $FE00
Address: $FE03
Reset:
Read:
Reset:
Write:
Read:
Write:
Figure 18-7. SIM Break Flag Control Register (SBFCR)
BCFE
Bit 7
Bit 7
R
R
R
0
Figure 18-6. SIM Break Status Register (SBSR)
= Reserved
= Reserved
R
6
R
6
MC68HC908GP32 Data Sheet, Rev. 10
R
5
R
5
R
4
R
4
1. Writing a 0 clears SBSW.
R
3
R
3
R
2
R
2
Note
SBSW
1
0
R
1
(1)
Break Module (BRK)
Bit 0
Bit 0
R
R
219