EP9312-IBZ Cirrus Logic Inc, EP9312-IBZ Datasheet - Page 284

• Manufacturer Part Number: EP9312-IBZ
• Description: IC ARM920T MCU 200MHZ 352-PBGA
• Manufacturer: Cirrus Logic Inc
• Series: EP9r

Specifications of EP9312-IBZ

• Core Size: 16/32-Bit
• Package / Case: 352-BGA
• Core Processor: ARM9
• Speed: 200MHz
• Connectivity: EBI/EMI, EIDE, Ethernet, I²C, IrDA, Keypad/Touchscreen, SPI, UART/USART, USB
• Peripherals: AC'97, DMA, I&sup2:S, LCD, LED, MaverickKey, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Controller Family/series: (ARM9)
• A/d Converter: 12 Bits
• No. Of I/o Pins: 65
• Clock Frequency: 200MHz
• Processor Series: EP93xx
• Core: ARM920T
• Data Bus Width: 32 bit
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 598-1260

8
8-20
Graphics Accelerator
EP93xx User’s Guide
Note: Setting the source direction bits different from the destination direction bits is illegal and
E. Write the desired value to the HEIGHT field in the
F. The
G. The INTEN bit must configured to enable or disable an interrupt signal to the ARM
H. After Step G is complete, write EN = ‘1’ to start the Block Copy function.
I. Wait for an interrupt or poll for EN = ‘0’. When the EN bit is cleared to ‘0’, the Block
will have unpredictable results.
10 - 1 = 9 = 0x9.
same size for the source and the destination. Setting the PACKD bit allows transfers
from images that are packed into whole word areas.
appropriate function.
for the appropriate function.
from the source to be compared with the transparency pixel pattern to determine if
the destination pixel is to be modified before it is written. Without this bit enabled, a
direct block copy would occur.
bits control the direction for the line accumulator, Y, and the word/pixel counter, X. In
a left to right and top to bottom transfer:
For example, a 20-pixels x 10-lines image has a height of 10 lines. So, HEIGHT =
The PACKD bit must be configured to indicate if the image to be copied has the
The P bits must be configured for the BPP depth of the image to be copied.
When using the AND/OR/XOR mask function, the M bits must be configured for the
When using the AND/OR/XOR destination function, the D bits must be configured
When using transparency, the TRANS bit must be enabled to ‘1’. This allows data
The SYDIR, SXDIR and DYDIR, DXDIR direction bits must be configured. These
refer to the note in
where HEIGHT = the height in lines of the image that is to be copied minus 1.
previous graphics instruction. The EOI bit field must be cleared to ‘0’ regardless of
the interrupt enable status.
Core that occurs upon completion of the acceleration function.
Copy function sequence is done.
(1).if the destination is not exactly the same as the source, or
(2).if the destination partially overlaps the source and has a destination starting
“BLOCKCTRL”
word address greater than the source starting word address, then the source
information may be corrupted before being read. For this condition, the
direction bits for the transfer must be changed from left to right and top to
bottom to right to left and bottom to top.
Section 8.5.2.4 on page
register must be cleared to 0x0. This action clears out the
Copyright 2007 Cirrus Logic
8-12.
“BLKDESTHEIGHT”
register,
DS785UM1