AT89LP214-20XU Atmel, AT89LP214-20XU Datasheet - Page 71

• Manufacturer Part Number: AT89LP214-20XU
• Description: MCU 8051 2K FLASH 20MHZ 14-TSSOP
• Manufacturer: Atmel
• Series: 89LPr

Specifications of AT89LP214-20XU

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 14-TSSOP
• Package: 14TSSOP
• Device Core: 8051
• Family Name: AT89
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 12
• Interface Type: SPI/UART
• Number Of Timers: 2
• Core: 8051
• Processor Series: AT89x
• Maximum Clock Frequency: 20 MHz
• Data Ram Size: 128 B
• Mounting Style: SMD/SMT
• Height: 1.05 mm
• Length: 5.1 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.4 V
• Width: 4.5 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

23.4
Table 23-3.
23.5
23.6
3538E–MICRO–11/10
Symbol
LOAD
SUCCESS
WRTINH
BUSY
Bit
Status Register
DATA Polling
Flash Security
Function
Load flag. Cleared low by the load page buffer command and set high by the next memory write. This flag signals that
the page buffer was previously loaded with data by the load page buffer command.
Success flag. Cleared low at the start of a programming cycle and will only be set high if the programming cycle
completes without interruption from the brownout detector.
Write Inhibit flag. Cleared low by the brownout detector (BOD) whenever programming is inhibited due to V
below the minimum required programming voltage. If a BOD episode occurs during programming, the SUCCESS flag
will remain low after the cycle is complete. WRTINH low also forces BUSY low.
Busy flag. Cleared low whenever the memory is busy programming or if write is currently inhibited.
Status
–
7
Register
The current state of the memory may be accessed by reading the status register. The status reg-
ister is shown in
The AT89LP213/214 implements DATA polling to indicate the end of a programming cycle.
While the device is busy, any attempted read of the last byte written will return the data byte with
the MSB complemented. Once the programming cycle has completed, the true value will be
accessible. During Erase the data is assumed to be FFH and DATA polling will return 7FH.
When writing multiple bytes in a page, the DATA value will be the last data byte loaded before
programming begins, not the written byte with the highest physical address within the page.
The AT89LP213/214 provides two Lock Bits for Flash Code Memory security. Lock bits can be
left unprogrammed (FFh) or programmed (00h) to obtain the protection levels listed in
4. Lock bits can only be erased (set to FFh) by Chip Erase. Lock bit mode 2 disables program-
ming of all memory spaces, including the User Signature Array and User Configuration Fuses.
User fuses must be programmed before enabling Lock bit mode 2 or 3. Lock bit mode 3 imple-
mented mode 2 and also blocks reads from the code memory; however, reads of the User
Signature Array, Atmel Signature Array, and User Configuration Fuses are still allowed.
Table 23-4.
Mode
Program Lock Bits (by address)
–
6
1
2
3
Lock Bit Protection Modes
Table
–
5
FFh
00h
00h
00h
23-3.
–
4
FFh
01h
FFh
00h
LOAD
Protection Mode
No program lock features
Further programming of the Flash is disabled
Further programming of the Flash is disabled and verify
(read) is also disabled; OCD is disabled
3
SUCCESS
2
AT89LP213/214
WRTINH
1
BUSY
0
CC
Table 23-
falling
71