LPC3141FET180,551 NXP Semiconductors, LPC3141FET180,551 Datasheet - Page 28

• Manufacturer Part Number: LPC3141FET180,551
• Description: IC ARM9 MCU USB OTG 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC3000r

Specifications of LPC3141FET180,551

• Package / Case: 180-TFBGA
• Core Processor: ARM9
• Core Size: 32-Bit
• Speed: 270MHz
• Connectivity: EBI/EMI, I²C, IrDA, MMC, PCM, SPI, UART/USART, USB OTG
• Peripherals: DMA, I²S, LCD, PWM, WDT
• Number Of I /o: 20
• Program Memory Type: ROMless
• Ram Size: 192K x 8
• Voltage - Supply (vcc/vdd): 1.1 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC31
• Core: ARM926EJS
• Data Bus Width: 32 bit
• Data Ram Size: 192 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 270 MHz
• Number Of Timers: 5
• Operating Supply Voltage: 1.2 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: OM11037
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935289711551

NXP Semiconductors
LPC3141_3143
Preliminary data sheet
6.19 Event router
The event router extends the interrupt capability of the system by offering a flexible and
versatile way of generating interrupts. Combined with the wake-up functionality of the
CGU, it also offers a way to wake-up the system from suspend mode (with all clocks
deactivated).
The event router has four interrupt outputs connected to the interrupt controller and one
wake-up output connected to the CGU as shown in
activated when an event (for instance a rising edge) is detected on one of the input
signals. The input signals of the event router are connected to relevant internal (control)
signals in the system or to external signals through pins of the LPC3141/3143.
This module has the following features:
Remark: All pins that can be used as GPIO are connected to the event router (see
Figure
in GPIO mode.
Fig 8. Event router block diagram
•
•
•
•
•
•
•
•
•
•
•
Provides programmable routing of input events to multiple outputs for use as
interrupts or wake up signals.
Input events can come from internal signals or from the pins that can be used as
GPIO.
Inputs can be used either directly or latched (edge detected) as an event source.
The active level (polarity) of the input signal for triggering events is programmable.
Direct events will disappear when the input becomes inactive.
Latched events will remain active until they are explicitly cleared.
Each input can be masked globally for all inputs at once.
Each input can be masked for each output individually.
Event detect status can be read for each output separately.
Event detection is fully asynchronous (no active clock required).
Module can be used to generate a system wake-up from suspend mode.
8). Note that they can be used to trigger events when in normal functional mode or
All information provided in this document is subject to legal disclaimers.
APB
Rev. 0.16 — 27 May 2010
input signals
internal
EVENT ROUTER
(GPIO configurable)
external pins
cgu wakeup
interrupt 0
interrupt 1
interrupt 2
interrupt 3
Figure
CONTROLLER
8. The output signals are
LPC3141/3143
INTERRUPT
CGU
002aae087
© NXP B.V. 2010. All rights reserved.
28 of 74