DF2377RVFQ33 Renesas Electronics America, DF2377RVFQ33 Datasheet - Page 471

IC H8S MCU FLASH 3V 384K 144LQFP

DF2377RVFQ33

Manufacturer Part Number
DF2377RVFQ33
Description
IC H8S MCU FLASH 3V 384K 144LQFP
Manufacturer
Renesas Electronics America
Series
H8® H8S/2300r
Datasheet

Specifications of DF2377RVFQ33

Core Processor
H8S/2000
Core Size
16-Bit
Speed
33MHz
Connectivity
I²C, IrDA, SCI, SmartCard
Peripherals
DMA, POR, PWM, WDT
Number Of I /o
97
Program Memory Size
384KB (384K x 8)
Program Memory Type
FLASH
Ram Size
24K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 16x10b; D/A 6x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 75°C
Package / Case
144-LQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DF2377RVFQ33
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
DF2377RVFQ33V
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
DF2377RVFQ33W
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
DF2377RVFQ33WV
Manufacturer:
Renesas Electronics America
Quantity:
10 000
EDREQ Pin Falling Edge Activation Timing: Figure 8.26 shows an example of single address
mode transfer activated by the EDREQ pin falling edge.
EDREQ pin sampling is performed in each cycle starting at the next rise of φ after the end of the
EDMDR write cycle for setting the transfer-enabled state.
When a low level is sampled at the EDREQ pin while acceptance via the EDREQ pin is possible,
the request is held within the EXDMAC. Then when activation is initiated within the EXDMAC,
the request is cleared, and EDREQ pin high level sampling for edge sensing is started. If EDREQ
pin high level sampling is completed by the end of the DMA single cycle, acceptance resumes
after the end of the single cycle, and EDREQ pin low level sampling is performed again; this
sequence of operations is repeated until the end of the transfer.
[1]
[2], [5] Request is cleared at end of next bus cycle, and activation is started in EXDMAC.
[3], [6] DMA cycle start; EDREQ pin high level sampling is started at rise of φ.
[4], [7] When EDREQ pin high level has been sampled, acceptance is resumed after completion of single cycle.
Figure 8.26 Example of Single Address Mode Transfer Activated by EDREQ Pin Falling
Acceptance after transfer enabling; EDREQ pin low level is sampled at rise of φ, and request is held.
(As in [1], EDREQ pin low level is sampled at rise of φ, and request is held.)
φ
EDREQ
Address bus
EDACK
DMA control
Channel
Idle
[1]
Minimum 3 cycles
Request
Bus release
[2]
clearance period
Single
[3]
Request
DMA single
Transfer source/
destination
Edge
Idle
Acceptance
resumed
[4]
Minimum 3 cycles
Request
Bus release
Rev.7.00 Mar. 18, 2009 page 403 of 1136
Section 8 EXDMA Controller (EXDMAC)
[5]
clearance period
Single
[6]
Request
Transfer source/
DMA single Bus release
destination
Idle
Acceptance
resumed
[7]
REJ09B0109-0700

Related parts for DF2377RVFQ33