AT80C51SND1C-ROTIL Atmel, AT80C51SND1C-ROTIL Datasheet - Page 99

• Manufacturer Part Number: AT80C51SND1C-ROTIL
• Description: IC MCU FLASH MP3 DECODER 80-TQFP
• Manufacturer: Atmel
• Series: 80Cr

Specifications of AT80C51SND1C-ROTIL

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, IDE/ATAPI, MMC, SPI, UART/USART, USB
• Peripherals: Audio, I²S, MP3, PCM, POR, WDT
• Number Of I /o: 44
• Program Memory Type: ROMless
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.3 V
• Data Converters: A/D 2x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP, 80-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Other names: AT80C51SND1CROTIL

4109L–8051–02/08
Reset Value = 0000 0000b
Table 92. USBADDR Register
USBADDR (S:C6h) – USB Address Register
Number
FEN
Bit
7
6
5
4
3
2
1
0
7
SDRMWUP
Mnemonic Description
SUSPCLK
RMWUPE
FADDEN
UPRSM
CONFG
UADD6
USBE
Bit
6
-
USB Enable Bit
Set this bit to enable the USB controller.
Clear this bit to disable and reset the USB controller, to disable the USB
transceiver an to disable the USB controllor clock inputs.
Suspend USB Clock Bit
Set to disable the 48 MHz clock input (Resume Detection is still active).
Clear to enable the 48 MHz clock input.
Send Remote Wake-Up Bit
Set to force an external interrupt on the USB controller for Remote Wake UP
purpose.
An upstream resume is send only if the bit RMWUPE is set, all USB clocks are
enabled AND the USB bus was in SUSPEND state for at least 5 ms. See
UPRSM below.
Cleared by software.
Reserved
The value read from this bit is always 0. Do not set this bit.
Upstream Resume Bit (read only)
Set by hardware when SDRMWUP has been set and if RMWUPE is enabled.
Cleared by hardware after the upstream resume has been sent.
Remote Wake-Up Enable Bit
Set to enabled request an upstream resume signaling to the host.
Clear after the upstream resume has been indicated by RSMINPR.
Note: Do not set this bit if the host has not set the DEVICE_REMOTE_WAKEUP
feature for the device.
Configuration Bit
This bit should be set by the device firmware after a SET_CONFIGURATION
request with a non-zero value has been correctly processed.
It should be cleared by the device firmware when a SET_CONFIGURATION
request with a zero value is received. It is cleared by hardware on hardware
reset or when an USB reset is detected on the bus (SE0 state for at least 32 Full
Speed bit times: typically 2.7 µs).
Function Address Enable Bit
This bit should be set by the device firmware after a successful status phase of a
SET_ADDRESS transaction.
It should not be cleared afterwards by the device firmware. It is cleared by
hardware on hardware reset or when an USB reset is received (see above).
When this bit is cleared, the default function address is used (0).
UADD5
5
UADD4
4
UADD3
3
AT8xC51SND1C
UADD2
2
UADD1
1
UADD0
0
99