AT91SAM9261-CJ-999 Atmel, AT91SAM9261-CJ-999 Datasheet - Page 20

• Manufacturer Part Number: AT91SAM9261-CJ-999
• Description: IC MCU ARM9 ULTRA LP 217LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9261-CJ-999

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 190MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: DMA, LCD, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 192K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• For Use With: AT91SAM9261-EK - KIT EVAL FOR AT91SAM926EJ-SAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -

8.1.2
8.1.2.1
8.1.2.2
20
AT91SAM9261 Preliminary
Boot Strategies
BMS = 1, Boot on Embedded ROM
BMS = 0, Boot on External Memory
The system always boots at address 0x0. To ensure a maximum number of possibilities for boot,
the memory layout can be configured with two parameters.
REMAP allows the user to lay out the first internal SRAM bank to 0x0 to ease development. This
is done by software once the system has booted for each Master of the Bus Matrix. Refer to the
Bus Matrix Section for more details.
When REMAP = 0, BMS allows the user to lay out to 0x0, at his convenience, the ROM or an
external memory. This is done via hardware at reset.
Note:
The AT91SAM9261 Bus Matrix manages a boot memory that depends on the level on the BMS
pin at reset. The internal memory area mapped between address 0x0 and 0x000F FFFF is
reserved for this purpose.
If BMS is detected at 1, the boot memory is the embedded ROM.
If BMS is detected at 0, the boot memory is the memory connected on the Chip Select 0 of the
External Bus Interface.
The system boots using the Boot Program.
The customer-programmed software must perform a complete configuration.
To speed up the boot sequence when booting at 32 kHz EBI CS0 (BMS=0), the user must take
the following steps:
• Downloads and runs an application from external storage media into internal SRAM
• Downloaded code size depends on embedded SRAM size
• Automatic detection of valid application
• Bootloader on a non-volatile memory
• SAM-BA
• Boot on slow clock (32,768 Hz)
• Boot with the default configuration for the Static Memory Controller, byte select mode, 16-bit
1. Program the PMC (main oscillator enable or bypass mode).
2. Program and start the PLL.
3. Reprogram the SMC setup, cycle, hold, mode timings registers for CS0 to adapt them
4. Switch the main clock to the new value.
data bus, Read/Write controlled by Chip Select, allows boot on 16-bit non-volatile memory.
– SDCard
– NAND Flash
– SPI DataFlash connected on NPCS0 of the SPI
– Serial communication on a DBGU
– USB Device HS Port
to the new clock
Memory blocks not affected by these parameters can always be seen at their specified base
addresses. See the complete memory map presented in
®
boot in case no valid program is detected in external NVM, supporting:
Figure 8-1 on page
6062M–ATARM–23-Mar-09
16.