MC56F8323VFB60 Freescale Semiconductor, MC56F8323VFB60 Datasheet - Page 87

• Manufacturer Part Number: MC56F8323VFB60
• Description: IC MPU HYBRID DSP 32K 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8323VFB60

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 60MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 27
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 2.25 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 64-LQFP
• For Use With: MC56F8323EVME - BOARD EVALUATION MC56F8323
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

6.5.1.2
6.5.1.3
Writing 1 to this field will cause the part to reset.
6.5.1.4
6.5.1.5
6.5.2
Bits in this register are set upon any system reset and are initialized only by a Power-On Reset (POR). A
reset (other than POR) will only set bits in the register; bits are not cleared. Only software should clear this
register.
6.5.2.1
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
6.5.2.2
When 1, this bit indicates that the previous reset occurred as a result of a software reset (write to SW RST
bit in the SIM CONTROL register). This bit will be cleared by any hardware reset or by software. Writing
a 0 to this bit position will set the bit, while writing a 1 to the bit will clear it.
Freescale Semiconductor
Preliminary
•
•
•
•
•
•
•
•
•
•
Base + $1
RESET
0 = OnCE clock to 56800E core enabled when core TAP is enabled
1 = OnCE clock to 56800E core is always enabled
00 = Stop mode will be entered when the 56800E core executes a STOP instruction
01 = The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can be
reprogrammed in the future
10 = The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can then only be
changed by resetting the device
11 = Same operation as 10
00 = Wait mode will be entered when the 56800E core executes a WAIT instruction
01 = The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can be
reprogrammed in the future
10 = The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can then only
be changed by resetting the device
11 = Same operation as 10
Read
Write
SIM Reset Status Register (SIM_RSTSTS)
OnCE Enable (ONCE EBL)—Bit 5
Software Reset (SW RST)—Bit 4
Stop Disable (STOP_DISABLE)—Bits 3–2
Wait Disable (WAIT_DISABLE)—Bits 1–0
Reserved—Bits 15–6
Software Reset (SWR)—Bit 5
15
0
0
Figure 6-4 SIM Reset Status Register (SIM_RSTSTS)
14
0
0
13
0
0
12
0
0
56F8323 Technical Data, Rev. 17
11
0
0
10
0
0
9
0
0
8
0
0
7
0
0
6
0
0
SWR
5
COPR
4
EXTR
3
POR
Register Descriptions
2
1
0
0
0
0
0
87