XR17D152CM-F Exar Corporation, XR17D152CM-F Datasheet - Page 22

• Manufacturer Part Number: XR17D152CM-F
• Description: IC UART PCI BUS DUAL 100TQFP
• Manufacturer: Exar Corporation
• Type: RS- 232 or RS- 422 or RS- 485r

Specifications of XR17D152CM-F

• Number Of Channels: 2, DUART
• Package / Case: 100-TQFP
• Features: *
• Fifo's: 64 Byte
• Protocol: RS485
• Voltage - Supply: 3.3V, 5V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 6.25 Mbps
• Supply Voltage (max): 5.25 V or 5.5 V
• Supply Voltage (min): 4.5 V or 4.75 V
• Supply Current: 4 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 5 V
• No. Of Channels: 2
• Uart Features: Tx/Rx FIFO Counters
• Supply Voltage Range: 3V To 5.5V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: TQFP
• No. Of Pins: 100
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1016-1288

XR17D152
UNIVERSAL (3.3V AND 5V) PCI BUS DUAL UART
The D152 includes an on-chip oscillator (XTAL1 and XTAL2). The crystal oscillator provides the system clock to
the Baud Rate Generators (BRG) in each of the 2 UARTs, the 16-bit general purpose timer/counter and
internal logics. XTAL1 is the input to the oscillator or external clock buffer input with XTAL2 pin being the output.
See Programmable Baud Rate Generator in the UART section for programming details.
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant with
10-22 pF capacitance load, 100ppm) connected externally between the XTAL1 and XTAL2 pins (see
Alternatively, an external clock can be connected to the XTAL1 pin to clock the internal 2 baud rate generators
for standard or custom rates. However, for external clock frequencies greater than 24MHz, a 2K pull-up may be
necessary on the XTAL2 output (see
further reading on oscillator circuit please see application note DAN108 on EXAR’s web site.
3.0 CRYSTAL OSCILLATOR / BUFFER
F
IGURE
F
IGURE
9. T
Figure
vcc
gnd
YPICAL OSCILLATOR CONNECTIONS
10. E
2 2 -4 7 pF
X T A L1
External Clock
10). Typically, the oscillator connections are shown in
C 1
R =3 0 0 K to 4 00 K
XTERNAL
R1
2K
1 4 .7 45 6
VCC
M H z
22
C
LOCK
2 2 -4 7 pF
X T A L2
XTAL1
XTAL2
C 2
C
ONNECTION FOR
E
XTENDED
D
áç
áç
áç
áç
ATA
Figure
R
ATE
Figure
REV. 1.2.0
9. For
9).