XR17D152CM-F Exar Corporation, XR17D152CM-F Datasheet - Page 46

• Manufacturer Part Number: XR17D152CM-F
• Description: IC UART PCI BUS DUAL 100TQFP
• Manufacturer: Exar Corporation
• Type: RS- 232 or RS- 422 or RS- 485r

Specifications of XR17D152CM-F

• Number Of Channels: 2, DUART
• Package / Case: 100-TQFP
• Features: *
• Fifo's: 64 Byte
• Protocol: RS485
• Voltage - Supply: 3.3V, 5V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 6.25 Mbps
• Supply Voltage (max): 5.25 V or 5.5 V
• Supply Voltage (min): 4.5 V or 4.75 V
• Supply Current: 4 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 5 V
• No. Of Channels: 2
• Uart Features: Tx/Rx FIFO Counters
• Supply Voltage Range: 3V To 5.5V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: TQFP
• No. Of Pins: 100
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1016-1288

XR17D152
UNIVERSAL (3.3V AND 5V) PCI BUS DUAL UART
This is an 8-bit general purpose register for the user to store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle.
FCTR [3:0] - Auto RTS/DTR Flow Control Hysteresis Select
These bits select the auto RTS/DTR flow control hysteresis and only valid when TX and RX Trigger Table-D is
selected (FCTR bit-6 and 7 are set to logic 1). The RTS/DTR hysteresis is referenced to the RX FIFO trigger
level. After reset, these bits are set to logic 0 selecting the next FIFO trigger level for hardware flow control.
Table 17
FCTR[4]: Infrared RX Input Logic Select
FCTR[5]: Auto RS485 Enable
Auto RS485 half duplex control enable/disable.
FCTR[7:6]: TX and RX FIFO Trigger Table Select
These 2 bits select the transmit and receive FIFO trigger level table A, B, C or D. When table A, B, or C is
selected the auto RTS flow control trigger level is set to "next FIFO trigger level" for compatibility to ST16C550
and ST16C650 series. RTS#/DTR# triggers on the next level of the RX FIFO trigger level, in another word, one
FIFO level above and one FIFO level below. See
6-7, i.e. if Table C is used on the receiver with RX FIFO trigger level set to 56 bytes, RTS/DTR# output will de-
assert at 60 and re-assert at 16.
5.8.12
5.8.13
Logic 0 = Select RX input as active high encoded IrDA data, normal, (default).
Logic 1 = Select RX input as active low encoded IrDA data, inverted.
Logic 0 = Standard ST16C550 mode. Transmitter generates an interrupt when transmit holding register
(THR) becomes empty. Transmit Shift Register (TSR) may still be shifting data bit out.
Logic 1 = Enable Auto RS485 half duplex direction control. RTS# output changes its logic level from HIGH to
LOW when finished sending the last stop bit of the last character out of the TSR register. It changes back to
HIGH from LOW when a data byte is loaded into the THR or transmit FIFO. The change to HIGH occurs prior
sending the start-bit. It also changes the transmitter interrupt from transmit holding to transmit shift register
(TSR) empty.
shows the 16 selectable hysteresis levels.
SCRATCH PAD REGISTER (SPR) - Read/Write
FEATURE CONTROL REGISTER (FCTR) - Read/Write
Table 14
46
for complete selection with FCR bit 4-5 and FCTR bit
áç
áç
áç
áç
REV. 1.2.0