XQ2V1000-4BG575N Xilinx Inc, XQ2V1000-4BG575N Datasheet - Page 49

• Manufacturer Part Number: XQ2V1000-4BG575N
• Description: FPGA 650MHZ CMOS1.5V 575-P
• Manufacturer: Xilinx Inc
• Series: QPro™ Virtex™-IIr

Specifications of XQ2V1000-4BG575N

• Number Of Labs/clbs: 1280
• Total Ram Bits: 737280
• Number Of I /o: 328
• Number Of Gates: 100000
• Voltage - Supply: 1.425 V ~ 1.575 V
• Mounting Type: Surface Mount
• Operating Temperature: -55°C ~ 125°C
• Package / Case: 575-BBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Logic Elements/cells: -
• Other names: Q5801737

Table 33: DC Characteristics Over Recommended Operating Conditions
Table 34: Quiescent Supply Current
Power-On Power Supply Requirements
Xilinx FPGAs require a certain amount of supply current
during power-on to ensure proper device operation. The
actual current consumed depends on the power-on ramp
rate of the power supply.
The V
ramp on no faster than 200 μs and no slower than 50 ms.
Ramp on is defined as: 0 V
Table 35
Virtex-II FPGAs for proper power on and configuration.
Power supplies can be turned on in any sequence.
If any V
draws up to 300 mA, worst case, until the V
on. This current draw does not harm the device. If the
current is limited to the minimum value above, or larger, the
device powers on properly after all three supplies have
passed through their power on reset threshold voltages.
DS122 (v2.0) December 21, 2007
Product Specification
Notes:
1.
Notes:
1.
2.
3.
4.
Symbol
Symbol
I
I
V
CCAUXQ
CCINTQ
I
I
CCOQ
V
I
I
I
DRINT
BATT
C
Internal pull-up and pull-down resistors guarantee valid logic levels at unconnected input pins. These pull-up and pull-down resistors do not
guarantee valid logic levels when input pins are connected to other circuits.
With no output current loads and no active input pull-up resistors. All I/O pins are 3-stated and floating.
If DCI or differential signaling is used, more accurate values can be obtained by using the Power Estimator or XPOWER.
Data are retained even if V
All values shown reflect the military temperature operating range. For industrial temperature operating range values, refer to
REF
RPU
RPD
DRI
I
L
IN
CCINT
CCO
shows the maximum current required by QPro
, V
bank powers up before V
R
Data retention V
Data retention V
V
Input leakage current
Input capacitance
Pad pull-up (when selected) @ V
Pad pull-down (when selected) @ V
Battery supply current
Quiescent V
Quiescent V
Quiescent V
REF
CCAUX
current per bank
, and V
CCINT
CCO
CCAUX
DC
CCO
CCINT
CCAUX
CCO
supply current
supply current
supply current
to minimum supply voltages.
drops to 0V.
power supplies shall each
voltage
voltage
Description
CCAUX
Description
(1)(2)
IN
, then each bank
(1)(2)
CCAUX
= 0V, V
IN
= 3.6V (sample tested)
powers
CCO
www.xilinx.com
= 3.3V (sample tested)
Note:
disappears even if V
Once initialized and configured, use the power calculator to
estimate current drain on these supplies.
Table 35: Maximum Power-On Current Required for
QPro Virtex-II Devices
Notes:
1.
2.
I
I
CCAUXMAX
CCINTMAX
I
I
All values shown reflect the military temperature operating range.
For industrial temperature operating range values, refer to
Current
CCOMAX
CCOMIN
The 300 mA is transient current (peak) and eventually
XQ2V1000
XQ2V3000
XQ2V6000
XQ2V1000
XQ2V3000
XQ2V6000
XQ2V1000
XQ2V3000
XQ2V6000
values listed here apply to the entire device (all banks).
Device
CCAUX
XQ2V1000
Device
QPro Virtex-II 1.5V Platform FPGAs
500
140
75
All
All
All
All
All
All
All
All
does not power up
Min
–
–
–
Device (mA)
XQ2V3000
Note 1
Note 1
Typical
1300
140
140
Min
–10
–10
12.5
1.2
2.5
12
27
45
10
1
2
2
5
Max
1300
1500
+10
+10
250
250
100
Max
6.25
6.25
6.25
500
105
150
10
[Ref
40
XQ2V6000
4].
1500
140
140
Units
Units
[Ref
μA
μA
μA
μA
nA
pF
mA
mA
mA
V
V
49
4].