MT47H32M16HR-3:F Micron Technology Inc, MT47H32M16HR-3:F Datasheet - Page 47

• Manufacturer Part Number: MT47H32M16HR-3:F
• Description: IC DDR2 SDRAM 512MBIT 3NS 84FBGA
• Manufacturer: Micron Technology Inc
• Type: DDR2 SDRAMr

Specifications of MT47H32M16HR-3:F

• Format - Memory: RAM
• Memory Type: DDR2 SDRAM
• Memory Size: 512M (32Mx16)
• Speed: 3ns
• Interface: Parallel
• Voltage - Supply: 1.7 V ~ 1.9 V
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 84-TFBGA
• Organization: 32Mx16
• Density: 512Mb
• Address Bus: 15b
• Access Time (max): 450ps
• Maximum Clock Rate: 667MHz
• Operating Supply Voltage (typ): 1.8V
• Package Type: FBGA
• Operating Temp Range: 0C to 85C
• Operating Supply Voltage (max): 1.9V
• Operating Supply Voltage (min): 1.7V
• Supply Current: 250mA
• Pin Count: 84
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 557-1466

Output Electrical Characteristics and Operating Conditions
Table 18: Differential AC Output Parameters
Figure 13: Differential Output Signal Levels
Table 19: Output DC Current Drive
PDF: 09005aef82f1e6e2
512MbDDR2.pdf - Rev. R 12/10 EN
Parameter
AC differential cross-point voltage
AC differential voltage swing
Parameter
Output MIN source DC current
Output MIN sink DC current
Notes:
Note:
V
V
TR
CP
1. The typical value of V
1. For I
2. For I
3. The DC value of V
4. The values of I
vice and V
which differential output signals must cross.
values of V
between 0V and 280mV.
are used to test device drive current capability to ensure V
V
ues are derived by shifting the desired driver operating point (see output IV curves)
along a 21Ω load line to define a convenient driver current for measurement.
IL,max
Output Electrical Characteristics and Operating Conditions
OH(DC)
OL(DC)
minus a noise margin are delivered to an SSTL_18 receiver. The actual current val-
; V
; V
OX(AC)
OUT
V
V
DDQ
DDQ
DDQ
Symbol
SSQ
Vswing
V
Vswing
OH(DC)
between V
OX(AC)
is expected to track variations in V
= 1.7V, V
= 1.7V, V
REF
and I
applied to the receiving device is set to V
OX(AC)
OUT
OL(DC)
OUT
DDQ
47
0.50 × V
is expected to be about 0.5 × V
= 280mV. V
= 1,420mV. (V
Crossing point
and V
are based on the conditions given in Notes 1 and 2. They
Min
Symbol
1.0
DDQ
V
I
I
DDQ
OH
OX
OL
Micron Technology, Inc. reserves the right to change products or specifications without notice.
- 125
- 280mV.
512Mb: x4, x8, x16 DDR2 SDRAM
OUT
OUT
/I
OL
- V
must be less than 21Ω for values of V
0.50 × V
Value
DDQ
–13.4
DDQ
13.4
)/I
. V
OH
Max
OX(AC)
DDQ
–
IH,min
DDQ
must be less than 21Ω for
© 2004 Micron Technology, Inc. All rights reserved.
+ 125
TT
of the transmitting de-
indicates the voltage at
plus a noise margin and
.
Units
mA
mA
Units
mV
mV
Notes
1, 2, 4
2, 3, 4
Notes
1
OUT