103H8221-5141/1 SANYO DENKI - SANMOTION, 103H8221-5141/1 Datasheet - Page 3

• Manufacturer Part Number: 103H8221-5141/1
• Description: STEPPER MOTOR, 1.8DEG, 2.4V
• Manufacturer: SANYO DENKI - SANMOTION

Specifications of 103H8221-5141/1

• Coil Type: Bipolar
• Torque Max: 2.74N-m
• Current Rating: 4A
• No. Of Phases: 2
• Resistance: 600mohm
• Inductance: 3.5mH
• External Depth: 62mm
• External Length / Height: 82mm
• External Width: 82mm
• Frame Size: 34

1. Do not use the product in an explosive, flammable or
2. Have a person with expert knowledge for performing
3. Do not work for wiring, maintenance servicing or
4. When the protective functions of the product is
5. Stepping motor may run out of order at the operating
6. Do not touch the internal parts of the PM driver. Doing
7. Do not connect the stepping motor directly with the
8. Use the electric power source within the rated input
9. Connect the PM driver and stepping motor to the
10. Do not harm, forcibly put a stress, or load a heavy
11. Perform wiring with the power cable as instructed by
12. Be sure not to touch the rotating part of the stepping
13. Neither reach or touch the electric terminals while
14. Never disconnect any of the connectors while electric power
corrosive atmosphere, watery place or near a combustible
material. Doing so may cause injury or fire.
the transportation, placement, wiring, operation,
maintenance or inspection of the product. Without
such knowledge, it may cause an electric shock, injury
or fire.
inspection with the electric power on. Perform either
of those five minutes after turning the power off, or
otherwise, it may cause an electric shock.
activated, turn the power off immediately and
eliminate the cause. If continuing the operation
without eliminating the cause, the product may
operate improperly and cause injury or a breakdown
of the system devices.
and stopping occasions, depending on the magnitude
of the load. Put the product into use after confirming
with the adequate trial test operation in the maximum
load conditions that the product performs reliable
operation. Doing otherwise may cause a breakdown
of the system. (Should the product run out of order in
the use to drive upward/downward, it may cause a fall
of the load.)
so may cause an electric shock.
commercial power outlet. Doing so may cause an
electric shock, injury or fire. The power shall be
supplied to the stepping motor through the driving
circuit.
voltage. Using otherwise may cause fire or an electric
shock.
ground. Using without grounding may cause an
electric shock.
article on the cable or get it caught between the
articles. Doing so may cause an electric shock.
the wiring diagram or the Operation Manual. Doing
otherwise may cause an electric shock or fire.
motor during its operation. Touching it may cause
injury.
electric power is on. Doing so may cause an electric
shock.
is on. Doing so may cause an electric shock and corruption.
＜General matters＞
＜Operation＞
DANGER
＜Wiring＞
1. Prior to placement, operation, maintenance servicing
2. Do not use the PM driver or the stepping motor
3. Do not insert a finger or a thing into the opening of the
4. Do not use the damaged PM driver or stepping motor.
5. Use the PM driver and stepping motor in the
6. Be careful that the temperature rises in the operating
7. Unpack while confirming the ceiling. Failure to do so
8. Confirm if the product is the one having been
9. Do not perform measurement of the insulation
10. Perform wiring conforming to the technical standards
11. Ensure that wiring has been correctly done. Operating
12. Take insulation process for the attached condenser or
13. Do not climb or attach a heavy article on the product.
14. Neither block nor stuff the aspiration/exhaust vent
15. Follow the instructions for the direction to place.
16. Keep a distance as instructed by the Operation
17. Place the product with a great care so as to prevent
18. Mount the product on an incombustible material such
or inspection, be sure to read the Operation Manual
and follow the instructions to perform those. Failure
to follow the instructions may cause an electric shock,
injury or fire.
outside the specified conditions. Doing so may cause
an electric shock, injury or fire.
product. Doing so may cause an electric shock, injury or fire.
Doing so may cause injury, fire or the like.
designated combination. Using otherwise may cause
fire or a trouble.
PM driver, stepping motor or peripheral devices.
Failure to be careful may cause a burn.
may cause injury.
ordered. Installing an incorrect product may cause a
breakdown.
resistance or withstand insulation voltage of the
product. Doing so may cause a breakdown. Instead,
contact with us for such inspection.
of electric facility or the internal rule. Doing otherwise
may cause burning or fire.
without correct wiring may cause the stepping motor
to run out of control and result in injury.
the external resistance connection terminals. Failure
to do so may cause an electric shock.
Doing so may cause injury.
with a foreign particle. Doing so may cause fire.
Failure to do so may cause a trouble.
Manual for the PM driver from the inner surface of the
control console or other devices. Failure to do so may
cause a trouble.
from the danger such as a tumble or a turnover.
as metal. Doing otherwise may cause fire.
＜General matters＞
＜Unpacking＞
＜Placement＞
CAUTION
＜Wiring＞
2