MT46H8M32LFB5-6 IT:H Micron Technology Inc, MT46H8M32LFB5-6 IT:H Datasheet - Page 91

• Manufacturer Part Number: MT46H8M32LFB5-6 IT:H
• Description: DRAM Chip DDR SDRAM 256M-Bit 8Mx32 1.8V 90-Pin VFBGA Tray
• Manufacturer: Micron Technology Inc
• Type: DDR SDRAMr

Specifications of MT46H8M32LFB5-6 IT:H

• Density: 256 Mb
• Maximum Clock Rate: 166 MHz
• Package: 90VFBGA
• Address Bus Width: 14 Bit
• Operating Supply Voltage: 1.8 V
• Maximum Random Access Time: 6.5|5 ns
• Operating Temperature: -40 to 85 °C
• Organization: 8Mx32
• Address Bus: 14b
• Access Time (max): 6.5/5ns
• Operating Supply Voltage (typ): 1.8V
• Package Type: VFBGA
• Operating Temp Range: -40C to 85C
• Operating Supply Voltage (max): 1.95V
• Operating Supply Voltage (min): 1.7V
• Supply Current: 120mA
• Pin Count: 90
• Mounting: Surface Mount
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Compliant

Figure 51: Power-Down Mode (Active or Precharge)
Deep Power-Down
PDF: 09005aef834bf85b
256mb_mobile_ddr_sdram_t36n.pdf - Rev. H 11/09 EN
Command
Address
DQS
CK#
CKE
DM
DQ
CK
No read/write
access in progress
t
t
t
IS
IS
IS
Valid
Valid
Notes:
T0
t
t
IH
t
2
IH
IH
Deep power-down (DPD) is an operating mode used to achieve maximum power reduc-
tion by eliminating power to the memory array. Data will not be retained after the
device enters DPD mode.
Before entering DPD mode the device must be in the all banks idle state with no activity
on the data bus (
LOW with RAS# and CAS# HIGH at the rising edge of the clock while CKE is LOW. CKE
must be held LOW to maintain DPD mode. The clock must be stable prior to exiting
DPD mode. To exit DPD mode, assert CKE HIGH with either a NOP or DESELECT com-
mand present on the command bus. After exiting DPD mode, a full DRAM initialization
sequence is required.
t
CK
1.
2. If this command is a PRECHARGE (or if the device is already in the idle state), then the
3. No column accesses can be in progress when power-down is entered.
power-down
t
HIGH at Ta2 (exit power-down).
power-down mode shown is precharge power-down. If this command is an ACTIVE (or if
at least 1 row is already active), then the power-down mode shown is active power-down.
t
CKE applies if CKE goes LOW at Ta2 (entering power-down);
IS
Enter
mode
NOP
T1
3
t
CH
Must not exceed refresh device limits
t
RP time must be met). DPD mode is entered by holding CS# and WE#
t
CL
T2
(
(
(
(
(
(
(
(
)
(
)
(
)
(
)
(
)
(
)
)
)
)
)
)
)
)
(
(
(
(
(
(
(
)
)
)
)
)
(
)
)
(
(
(
(
(
)
)
)
)
)
)
t
CKE
91
256Mb: x16, x32 Mobile LPDDR SDRAM
Ta0
Micron Technology, Inc. reserves the right to change products or specifications without notice.
power-down
mode
NOP
Ta1
Exit
t
t
XP
CKE
1
1
Valid
©2008 Micron Technology, Inc. All rights reserved.
Valid
Ta2
t
XP applies if CKE remains
Power-Down
Don’t Care
Tb1