XRT91L31IQTR-F Exar Corporation, XRT91L31IQTR-F Datasheet - Page 24

• Manufacturer Part Number: XRT91L31IQTR-F
• Description: SONET SDH - 8 Bit OC12/STM4, OC3/STM1 PHY Transceiver (with Improved Jitter Transfer Used For Loop Timing Applications)
• Manufacturer: Exar Corporation
• Type: Transceiverr

Specifications of XRT91L31IQTR-F

• Input: LVCMOS, LVPECL, LVTTL
• Output: LVCMOS, LVPECL, LVTTL
• Frequency - Max: 77.76MHz
• Voltage - Supply: 3.135 V ~ 3.465 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-FQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

XRT91L31
STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
The transmit section of the XRT91L31 accepts 8-bit parallel data and converts it to serial Differential LVPECL
data output intented to interface to an optical module. It consists of an 8-bit parallel Single-Ended LVTTL
interface, Parallel-to-Serial Converter, a clock multiplier unit (CMU), a Low Voltage Positive-referenced Emitter-
Coupled Logic (LVPECL) differential line driver, and Loop Timing modes. The LVPECL serial data output rate is
622.08 Mbps for STS-12/STM-4 applications and 155.52 Mbps for STS-3/STM-1 applications. The high
frequency serial clock is synthesized by a PLL, which uses a low frequency clock as its input reference. In
order to synchronize the data transfer process, the synthesized 622.08 MHz for STS-12/STM-4 or 155.52 MHz
STS-3/STM-1 serial clock output is divided by eight and the 77.76 MHz (STS-12/STM-4) or 19.44 MHz (STS-3/
STM-1) clock respectively is presented to the framer/mapper device to be used as its timing source.
The parallel data from an framer/mapper device is presented to the XRT91L31 through an 8-bit Single-Ended
LVTTL parallel bus interface TXDI[7:0]. To directly interface to the XRT91L31, the SONET Framer/ASIC must
be synchronized to the same timing source TXPCLK_IO in presenting data on the parallel bus interface. The
data must meet setup and hold times with respect to TXPCLK_IO. This clock output source is used to
synchronize the SONET Framer/ASIC to the XRT91L31. The framer/mapper device should use TXPCLK_IO
as its timing source so that parallel data is phase aligned with the serial transmit data. The data is latched into
a parallel input register on the rising edge of TXPCLK_IO. TXPCLK_IO is derived from a divide-by-8 of the high
speed synthesized clock resulting in a 77.76/ 19.44 MHz Single-Ended LVTTL clock output source to be used
by the framer/mapper device for parallel bus synchronization. A simplified block diagram of the transmit
parallel bus clock output system interface is shown in
F
3.0 TRANSMIT SECTION
3.1
IGURE
11. T
Transmit Parallel Input Interface
RANSMIT
P
ARALLEL
SONET Framer/ASIC
I
NPUT
I
NTERFACE
TXDI[7:0]
B
LOCK
TXPCLK_IO
8
Figure
24
VDD+
11.
PIO_CTRL
TTLREFCLK
STS-12/STM-4
STS-3/STM-1
Transceiver
XRT91L31
REFCLKP
or
REFCLKN
CMUREFSEL
REV. 1.0.2