PNX1500E/G,557 NXP Semiconductors, PNX1500E/G,557 Datasheet - Page 214

• Manufacturer Part Number: PNX1500E/G,557
• Description: IC MEDIA PROC 240MHZ 456-BGA
• Manufacturer: NXP Semiconductors

Specifications of PNX1500E/G,557

• Applications: Multimedia
• Core Processor: TriMedia
• Controller Series: Nexperia
• Interface: I²C, 2-Wire Serial
• Number Of I /o: 61
• Voltage - Supply: 1.14 V ~ 1.26 V
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 456-BGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Program Memory Type: -
• Ram Size: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 568-1296; 935277746557; PNX1500E/G

NXP Semiconductors
Volume 1 of 1
Table 8: Binary Sequence for the Section of the Flash Boot
PNX15XX_PNX952X_SER_N_4
Product data sheet
NOR Flash
8-bit Mode
0x1bf0_4005
0x0000_0002
0x5550_0000
0x0000_0155
0x1be4_0814
0x0000_0C09
0x1be4_080c
0x0000_0296
0x000f_0002
0x1bf0_0038
TM32_DRAM_HI
0x1bf0_0048
0x0010_0000
0x1bf0_0030
0x8000_0000
16-bit Mode
0x0080_0C09
0x0007_8002
3.2.1 Binary Sequence for the Section of the Flash Boot
3.3 The Specifics of the Host-Assisted Mode
In host-assisted boot mode the PNX15xx/952x Series is in a configuration where an
external CPU, such as an external MIPS
In that case, the PNX15xx/952x Series behaves as a plug-in PCI device. Most of the
responsibility of booting is taken care of by the host PCI BIOS and by the PNX15xx/
952x Series driver. However, there is still a requirement for a boot script in order to
initialize the hardware and get it ready to act as a recognizable PCI device. In addition
to the common boot script sequence, the only extra step required is to set a:
Since these IDs are vendor specific any PCI plug-in board based on PNX15xx/952x
Series requires an external EEPROM. This EEPROM has the responsibility to bring
the system into a good initial state (can be similar to the data presented in
Section
•
•
PCI Subsystem Vendor ID. This is a 16-bit value that identifies the board vendor.
NXP has the code 0x1131. Manufacturers of PCI plug-in cards for the open
market must obtain and use their own ID (from the PCI Special Interest
Group)[2].
Subsystem ID. This is a 16-bit value established by the board vendor to identify a
particular board. This is allocated by the vendors PCI Special Interest Group
representative. This value is used to identify a suitable driver for PC plug-and-
play.
NAND Flash
8-bit Mode
0x006A_8411
0x000a_8002
3.1.1) and to personalize the Subsystem ID and Subsystem Vendor ID.
Rev. 4.0 — 03 December 2007
16-bit Mode
0x00EA_8411
0x0006_1282
TM
Comments
Enables the functional mode of XIO_ACK and
XIO_D[15:8] pins instead of the GPIO mode
(default after RESET).
XIO Profile 0
Start the 8-Kilobyte data fetch from the Flash
memory device.
Waits for the completion of the 8-Kilobyte fetch.
TM32_DRAM_HI depends upon the state of the
BOOT_MODE[6:4] pins.
TM3260 starts executing code from
TM32_DRAM_START set to 1 Megabyte.
Start TM3260.
, x86, PowerPC
PNX15xx/952x Series
TM
Chapter 6: Boot Module
, or SH-5
© NXP B.V. 2007. All rights reserved.
TM
is the host.
6-214