MPC8343VRAGDB Freescale Semiconductor, MPC8343VRAGDB Datasheet - Page 75

• Manufacturer Part Number: MPC8343VRAGDB
• Description: IC MPU POWERQUICC II 620-PBGA
• Manufacturer: Freescale Semiconductor
• Series: PowerQUICC II PROr

Specifications of MPC8343VRAGDB

• Processor Type: MPC83xx PowerQUICC II Pro 32-Bit
• Speed: 400MHz
• Voltage: 1.2V
• Mounting Type: Surface Mount
• Package / Case: 620-PBGA
• Processor Series: MPC8xxx
• Core: e300
• Data Bus Width: 32 bit
• Development Tools By Supplier: MPC8349E-MITXE
• Maximum Clock Frequency: 400 MHz
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• I/o Voltage: 1.8 V, 2.5 V, 3.3 V
• Minimum Operating Temperature: 0 C
• Core Size: 32 Bit
• Program Memory Size: 64KB
• Cpu Speed: 400MHz
• Embedded Interface Type: I2C, SPI, USB, UART
• Digital Ic Case Style: BGA
• No. Of Pins: 620
• Rohs Compliant: Yes
• Family Name: MPC83xx
• Device Core: PowerQUICC II Pro
• Device Core Size: 32b
• Frequency (max): 400MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 1.2V
• Operating Supply Voltage (max): 1.26V
• Operating Supply Voltage (min): 1.14V
• Operating Temp Range: 0C to 105C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 620
• Package Type: BGA
• For Use With: CWH-PPC-8343N-VX - KIT EVAL SYSTEM QUICCSTART 8248CWH-PPC-8343N-VE - EVALUATION SYSTEM QUICC MPC8343E
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

However, while HRESET is asserted, these pins are treated as inputs, and the value on these pins is latched
when PORESET deasserts. Then the input receiver is disabled and the I/O circuit takes on its normal
function. Careful board layout with stubless connections to these pull-up/pull-down resistors coupled with
the large value of the pull-up/pull-down resistor should minimize the disruption of signal quality or speed
for the output pins.
21.7
The MPC8343EA requires high resistance pull-up resistors (10 kΩ is recommended) on open-drain pins,
including I
For more information on required pull-up resistors and the connections required for the JTAG interface,
refer to application note AN2931, PowerQUICC Design Checklist.
22 Ordering Information
This section presents ordering information for the device discussed in this document, and it shows an
example of how the parts are marked.
22.1
Table 62
individual part numbers correspond to a maximum processor core frequency. Each part number also
contains a revision code that refers to the die mask revision number. For available frequency configuration
Freescale Semiconductor
shows an analysis of the Freescale part numbering nomenclature for the MPC8343EA. The
Pull-Up Resistor Requirements
Part Numbers Fully Addressed by This Document
2
MPC8343EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 10
C pins, and IPIC interrupt pins.
The information in this document is accurate for revision 3.x silicon and
later (in other words, for orderable part numbers ending in A or B). For
information on revision 1.1 silicon and earlier versions, see the MPC8343E
PowerQUICC II Pro Integrated Host Processor Hardware Specifications
(Document Order No. MPC8343EEC).
NOTE
Ordering Information
75