AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 227

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 16-7. Refresh Cycle Followed by a Read Access
16.7.6
16.7.6.1
32072G–11/2011
SDRAMC_A[12:0]
D[15:0]
(input)
SDWE
SDCS
SDCK
RAS
CAS
Power Management
Self refresh mode
Row n
Col c Col d
Dnb
Dnc
Three low power modes are available:
The SDRAMC activates one low power mode as soon as the SDRAM device is not selected. It is
possible to delay the entry in self refresh and power-down mode after the last access by config-
uring the Timeout field in the Low Power Register (LPR.TIMEOUT).
This mode is selected by writing the value one to the Low Power Configuration Bits field in the
SDRAMC Low Power Register (LPR.LPCB). In self refresh mode, the SDRAM device retains
data without external clocking and provides its own internal clocking, thus performing its own
auto refresh cycles. All the inputs to the SDRAM device become “don’t care” except SDCKE,
which remains low. As soon as the SDRAM device is selected, the SDRAMC provides a
sequence of commands and exits self refresh mode.
Some low power SDRAMs (e.g., mobile SDRAM) can refresh only one quarter or a half quarter
or all banks of the SDRAM array. This feature reduces the self refresh current. To configure this
feature, Temperature Compensated Self Refresh (TCSR), Partial Array Self Refresh (PASR)
• Self refresh mode: the SDRAM executes its own auto refresh cycles without control of the
• Power-down mode: auto refresh cycles are controlled by the SDRAMC. Between auto
• Deep power-down mode (only available with mobile SDRAM): the SDRAM contents are lost,
Dnd
SDRAMC. Current drained by the SDRAM is very low.
refresh cycles, the SDRAM is in power-down. Current drained in power-down mode is higher
than in self refresh mode.
but the SDRAM does not drain any current.
t
RP
= 3
t
RC
= 8
Row m
t
RCD
= 3
Col a
CAS = 2
Dma
227