AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 338

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32072G–11/2011
Figure 19-13. Multi-Block DMA Transfer with Source Address Auto-reloaded and Linked List
The DMA Transfer flow is shown in
17. The DMACA fetches the next LLI from memory location pointed to by the current LLPx
a. If interrupts are enabled (CTLx.INT_EN = 1) and the block complete interrupt is un-
b. If interrupts are disabled (CTLx.INT_EN = 0) or the block complete interrupt is
register, and automatically reprograms the DARx, CTLx and LLPx channel registers.
Note that the SARx is not re-programmed as the reloaded value is used for the next
DMA block transfer. If the next block is the last block of the DMA transfer then the CTLx
and LLPx registers just fetched from the LLI should match Row 1 or Row 5 of
1 on page
338.
Address of
Source Layer
masked (MaskBlock[x] = 1’b1, where x is the channel number) hardware sets the
block complete interrupt when the block transfer has completed. It then stalls until
the block complete interrupt is cleared by software. If the next block is to be the last
block in the DMA transfer, then the block complete ISR (interrupt service routine)
should clear the CFGx.RELOAD_SR source reload bit. This puts the DMACA into
Row1 as shown in
the DMA transfer, then the source reload bit should remain enabled to keep the
DMACA in Row 7 as shown in
masked (MaskBlock[x] = 1’b0, where x is the channel number) then hardware does
not stall until it detects a write to the block complete interrupt clear register but
starts the next block transfer immediately. In this case, software must clear the
source reload bit, CFGx.RELOAD_SR, to put the device into Row 1 of
on page 326
Destination Address
SAR
326. The DMA transfer might look like that shown in
Source Blocks
before the last block of the DMA transfer has completed.
Table 19-1 on page
Figure 19-14 on page
Table 19-1 on page
326. If the next block is not the last block in
DAR(N)
DAR(1)
DAR(2)
DAR(0)
Destination Blocks
BlockN
Block0
Block1
Block2
339.
326.
Figure 19-13 on page
Destination Layer
Address of
Table 19-1
Table 19-
338